Attention After Submersion | Guardian Technologies 04759-2, 04760-2

Image 23

Guardian Technologies 04759-2 Attention After Submersion, Corrosion Protection, Out Of Service Procedure, Maintenance

Contents

 Not intended for use as Primary Power in place of utility  Models 04758-2 6 kW NG, 7 kW LP 04759-2 12 kW NG, 12 kW LP04760-2 13 kW NG, 15 kW LP This manual should remain with the unit INTRODUCTION ‹ CONTENTS‹ OPERATION AND MAINTENANCE ‹ HOW TO OBTAIN SERVICE Section 5 - Troubleshooting Section 2 - Post Installation Start-upand Adjustments Section 4 - Maintenance This product contains or emits chemicals  GENERAL HAZARDS IMPORTANT SAFETY INSTRUCTIONS  WARNING  ‹ STANDARDS INDEX  ELECTRICAL HAZARDS  FIRE HAZARDS   EXPLOSION HAZARDS  DANGER 1.1 UNPACKING/INSPECTION1.2 PROTECTION SYSTEMS 1.3 SYSTEM SET LED Figure 1.2 - 12 kW/15 kW, V-twin GT-990/760 Engine 1.4 THE GENERATORFigure 1.1 - 7 kW, Single Cylinder GH-410 Engine ‹ 1.5.2 ENGINE 1.5 SPECIFICATIONS‹ 1.5.1 GENERATOR DANGER 1.8 RECONFIGURING THE FUEL SYSTEM1.6 FUEL REQUIREMENTS AND RECOMMENDATIONS 1.7 FUEL CONSUMPTION Figure 1.4 - Demand Regulator 1.9 LOCATION‹ 1.8.2 12KW AND 15KW, 990CC ENGINES ‹ 1.9.1 GENERATOR Figure 1.5 - Battery Cable Connections 1.10 BATTERY INSTALLATION1.11 THE BATTERY ‹ 1.9.2 TRANSFER SWITCH 1.9.2.1 7 kW, 12 kW and 15 kW Units Section 2 - Post Installation Start-up and Adjustments 2.2 CHECK TRANSFER SWITCH OPERATION2.1 BEFORE INITIAL START-UP 2.3 ELECTRICAL CHECKS 2.5 CHECKING AUTOMATIC OPERATION 2.4 GENERATOR TESTS UNDER LOAD Figure 2.1 - Dual Fuel Regulators 2.6 ADJUSTING THE REGULATOR NATURAL GAS ONLYFigure 2.2 - Placement of Regulator Figure 2.5 - V-twin Full Load Speed Adjust Screw 2.7 ENGINE GOVERNOR ADJUSTMENTFigure 2.3 - Single Cylinder Engine Governor Adjustment Figure 2.4 - V-twin Engine Governor Adjustment ‹ 3.2.1 “AUTO” POSITION 2.8 VOLTAGE REGULATOR ADJUSTMENT3.1 BREAK-IN PROCEDURE Figure 2.6 - Voltage Adjustment Potentiometer ‹ 3.5.1 TRANSFER TO GENERATOR POWER SOURCE 3.3 AUTOMATIC TRANSFER OPERATION3.4 SEQUENCE OF AUTOMATIC OPERATION 3.5 MANUAL TRANSFER OPERATION Figure 3.2 - Manual Transfer Switch Operation 3.6 SETTING THE EXERCISE TIMER‹ 3.5.2 TRANSFER BACK TO UTILITY POWER SOURCE ‹ 3.7.1 LOW OIL PRESSURE SWITCH 4.2 CHECKING THE ENGINE OIL LEVEL ‹ 3.7.2 HIGH TEMPERATURE SWITCHFigure 3.3 - Low Oil Pressure and High Temperature Switches 4.1 FUSE 4.4 CHANGING THE OIL FILTER 4.5 CHANGING THE ENGINE AIR CLEANER‹ 4.3.2 OIL CHANGE PROCEDURE 4.3 CHANGING THE ENGINE OIL Figure 4.8 - Setting the Spark Plug Gap 4.7 BATTERY MAINTENANCEFigure 4.6 - 7 kW, Engine Air Cleaner Location Figure 4.7 - 12 kW and 15 kW Engine Air Cleaner 4.9 COOLING SYSTEM 4.8 ADJUSTING VALVE CLEARANCEFigure 4.10 - Valve Clearance Adjustment 4.10 ATTENTION AFTER SUBMERSION 4.12 OUT OF SERVICE PROCEDURE‹ 4.12.1 REMOVAL FROM SERVICE ‹ 4.12.2 RETURN TO SERVICE be performed by the nearest Authorized Dealer 4.13 SERVICE SCHEDULEATTENTION It is recommended that all service work Correction 5.1 TROUBLESHOOTING GUIDEProblem Cause Section 6 - Electrical Data ENGINE WIRING CONNECTION CONTROL PANEL BOXCUSTOMER Electrical Schematic - 12 & 15 kW - Drawing No. 0D8501-B Section 6 - Electrical Data Section 6 - Electrical Data ENGINE WIRING CUSTOMER 224A 225A Electrical Schematic - 7 kW - Drawing No. 0D9014-C PRE PACKAGED UNITS ONLY Section 7 - Exploded Views and Parts Lists FOAM, BACK EXHAUST ENCLOSURE COVER PART NO. QTY. DESCRIPTIONCLOTH, HARDWARE 266.7mm x 146mm 7KW FOAM, EXHAUST SIDE ENCLOSURE FRONT Section 7 - Exploded Views and Parts Lists DESCRIPTION PART NO. QTY 72 27, 28 73 3, 32, 33, 34, 35, 36, 40 Views and Parts Lists66 2, 5, 19, 20, 39, 40, 47, 64, 93 67 8, 11, 12 68 4, 5 69 16A, 16B, 17 ROLLER BEARING, GOVERNOR PLATE ASSEMBLY, CRANKCASE HOUSING WITHASSEMBLY, CRANKSHAFT HORIZONTAL ITEM PART NO. QTY. DESCRIPTION Section 7 - Exploded Views and Parts Lists ASSY, IGNITION COIL GV-990 CYLINDER 7 kW Generator - Drawing No. 0D3504-E 1.25 FT 1.8 FT 32 31 12 kW and 15 kW Generator - Drawing No. 0D3417-L 1.44 FT 2.6 FT3 FT Section 7 - Exploded Views and Parts Lists DESCRIPTION Section 7 - Exploded Views and Parts Lists Section 7 - Exploded Views and Parts Lists DESCRIPTION Section 7 - Exploded Views and Parts Lists Section 7 - Exploded Views and Parts Lists DESCRIPTION Air-cooled ALL DIMENSIONS IN MILLIMETERS INCHESSection 8 - Mounting Drawing No Section 9 - Notes CALIFORNIA AND FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONSMANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE PURCHASER’S/OWNER’S WARRANTY RESPONSIBILITIES EMISSION RELATED PARTS INCLUDE THE FOLLOWING EMISSION CONTROL SYSTEM WARRANTY PREPACKAGED EMERGENCY AUTOMATIC STANDBY GENERATORS GENERAC POWER SYSTEMS TWO YEAR LIMITED WARRANTY FOR GUARDIANWARRANTY SCHEDULE THIS WARRANTY SHALL NOT APPLY TO THE FOLLOWING

Guardian Technologies 04759-2 Attention After Submersion, Corrosion Protection, Maintenance

Models: 04759-2 04758-2 04760-2