Guardian Technologies 04758-2 Location, ‹ 1.8.2 12KW AND 15KW, 990CC ENGINES, ‹ 1.9.1 GENERATOR

Section 1 — General Information

Air-cooled 7 kW, 12 kW and 15 kW Generators

NOTE:

The natural gas adjustment screw is preset dur- ing installation and should not need any further adjustment.

‹1.8.2 12KW AND 15KW, 990CC ENGINES

To reconfigure the fuel system from NG to LP, follow these steps:

NOTE:

13.To adjust the system to run on LP fuel, turn BOTH adjuster screws 1/2 TURN CLOCKWISE. The system should now be set for maximum power and best perfomance. DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE SET PINS FROM THE REGULATOR HOUSING. THIS WILL VOID THE WARRANTY.

Figure 1.4 - Demand Regulator

The primary regulator for the propane supply is NOT INCLUDED with the generator. A fuel pres- sure of 11 to 14 inches of water column (0.4 to

0.5psi) to the fuel inlet of the generator MUST BE SUPPLIED.

1.	Turn off the gas supply. (if connected)
2.	Open the roof and remove the door.
3.	Remove the battery. (if installed)
4.	Remove the engine air in baffle located on the left-
	hand side of the battery compartment. Two M6
	screws are located on top of the baffle and two

IDLE CIRCUIT PORT

	OUTLET PORTS
	FUEL HOSE
	BRASS HOSE
	FITTING
U	BRASS HOSE
T	FITTING
1
	TAP
	1/8 NPT
	ADJUSTER
	SCREWS

SMALL

FUEL JET

REGULATOR HOUSING PORT

	M6 screws are located on the inside of the baffle
	towards the back.
5.	Remove the small hose clamp and hose from the
	fuel regulator. It may be necessary to pry the hose
	off of the brass fitting using a screwdriver to gen-
	tly lift up the hose edge.
6.	Remove the small brass hose fitting from the
	regulator casting.
7.	Place the small fuel jet, thread side first, into the
	threaded hole originally occupied by the brass
	hose fitting (Figure 1.4).
8.	Using a short No. 2 Phillips screw driver, thread
	the small fuel jet into the regulator casting. Do
	not over tighten.
9.	Apply thread sealant to the threads of the hose
	fitting and replace it into the regulator body.
10.	Re-attach the small hose and hose clamp and
	tighten as necessary.
11.	Replace the engine air in baffle using the four M6
	screws.
12.	Identify both brass adjustment screws on the
	regulator.

NOTE:

One adjustment screw can be accessed from the front of the unit and the second can be accessed from the back of the unit enclosure by removing the plastic hole plug. The screw can be turned with a long flat blade screwdriver.

14.It may be necessary to make minor adjustments to the preset adjustment screw settings to achieve maximum power, particularly at higher altitudes. If experiencing problems with the unit producing maximum power, follow the procedure in Section 2.6 (Adjusting the Fuel Regulator).

1.9LOCATION

‹1.9.1 GENERATOR

Install the generator set, in its protective enclosure, outdoors, where adequate cooling and ventilating air is always available. Consider these factors:

•Install the unit where air inlet and outlet open- ings will not become obstructed by leaves, grass, snow, etc. If prevailing winds will cause blowing or drifting, consider using a windbreak to protect the unit.

•Install the generator on high ground where water levels will not rise and endanger it.

•Allow sufficient room on all sides of the generator for maintenance and servicing. A good rule is to allow three feet of space on all sides.

•Where strong prevailing winds blow from one direction, face the generator air inlet openings to the prevailing winds.

•Install the generator as close as possible to the fuel supply, to reduce the length of piping.

•Install the generator as close as possible to the transfer switch. HOWEVER, REMEMBER THAT LAWS OR CODES MAY REGULATE THE DISTANCE.

8