62 0 Prepare a 3” white wire. Connect one end to RY lug #4. (S). Connect the other end to red output termi- nal LR. (S).
63 [7 Prepare another 3” white wire. Connect one end to RY lug #6. (S). Connect the other end to output terminal RR. (S).
64 0 Prepare a 16”green wire. Connect one end to black output terminal LB. (S). Connect the other end close to the center of the bare wire between the two capacitors. (S).
65 0 Prepare an 18” green wire. Connect one end to out- put terminal RB. (S). Connect the other end to the bare wire between the two capacitors. (S).
66 q Prepare an
67 0 Prepare a 7” white wire. Connect one end to FL lug #3. (S). Connect the other end to CL lug #l.
68 0 Prepare a 12”white wire. Connect one end to FR lug #7. (S). Place this against the chassis and connect it to CL lug #l.
69 0 Prepare a 13” white wire. Connect one end to CL lug #l.
70 0 Prepare a 7 1/2’ green wire. Connect one end to FR lug #8. (S). Connect the other end to CR lug #4.
71 0 Prepare another 8”green wire. Connect one end to CR lug #4.
72 0 Strip a 3/4" piece of light wire bare. Connect it be- tween the short ground lug of input socket LS and the separate ground lug between the 2 input soc- kets.
73 0 Prepare a 14” black wire, but strip 3/4" of insulation from one end. Thread the longer bared end through the separate ground lug, and connect it to the short ground lug of input socket RS. Solder only the two wires at the center ground lug at this time. Place the wire against the chassis, and connect the other end to the bare wire between the two large capacitors.
(S). This is the 4th of 7 wires connected at this point. Remember to leave space in the exact center for the last wire, but keep all of these close to- gether.
Now place the wired amplifier module behind the chassis in line with the input sockets, so that it is resting on the foam gasket, with the mounting feet against the chassis. Its wires will protrude toward the chassis, or to the right.
74 q Select the yellow and black twisted pair from the left side of the module. Connect the black wire to the short ground lug of input socket LS.
75 0 Select the red and black pair from the right side, and connect the black wire to the short lug of input socket RS.
76 0 Select the twisted white pair from the left side. Connect the longer wire to the side lug of the fuse holder LE (S). Connect the other wire to the tip lug of LF. (S).
77 0 Select the twisted white pair from the right side. Connect the longer wire to the side lug of RF (S). Connect the other wire to the tip lug of RF (S).
Make sure that all of the unconnected long wires (except for the green wires to eyelet 7 on each board) are placed off to the right so that when the module is installed on the chassis these wires will protrude between the feet below the right circuit board. The wires to the #7 eyelets, as well as those to eyelets 3 and 10, connect towards the front of the amplifier. Carefully lift the module without touching the components on the circuit boards. Swing it into posi- tion on the chassis, and check to make sure that no wires are trapped under the mounting feet. Make sure that the input socket long lugs have not been bent so that any shorts are possible
It is a good idea at this time to check the fan by hand, to make sure it rotates freely. Shipping sometimes may cause a misalignment. If it rubs, bending a strut will correct the problem.
78 0 Select 4 sheet metal screws and secure the module to the chassis. The easiest procedure may be to tilt the whole assembly backwards so that the module is again lying on the gasket, giving you access to the bottom of the chassis. Start the screws, and then check again to make sure no wires are trapped be- fore tightening the screws fully.
79 0 Select the green and white twisted pair from the bottom of the module. Connect the green wire to the terminal strip LT lug #l. Connect this wire to the lower hole in that lug, and solder it separately from the two wires which are soldered to the upper part of the lug, Make sure all 3 wires are soldered. Connect the white wire to LT lug #4. Use the lower hole for this wire, and solder it separately now. Do not solder the capacitor lead to the upper part of the lug at this time.
12
