Name of Parts | Wire Controller |
13 | 14 | 15 16 | 17 | 18 | 19 |
| 21.Clock button |
|
|
|
|
|
| ||
|
|
|
|
|
| Used to calibrate the time of | |
12 |
|
|
|
|
|
| |
11 |
|
|
|
|
|
| timer and clock |
|
|
|
|
|
| 22.Setting button | |
10 |
|
| MODE | FAN | SWING |
| |
9 | AUTO |
| TEMP |
| 20 | Used to confirm the time | |
8 |
|
|
|
|
| 21 | of timer and clock |
7 |
|
| CLOCK |
| SET | ||
|
|
| 22 | 23.Sleep button | |||
6 | SET |
| TIMER |
| SLEEP | ||
|
|
| 23 | Used to set Sleep state or | |||
5 | ROOM |
|
|
|
| ||
|
|
|
| RESET | 24 | Power Failure Resume | |
4 |
|
| FILTER RESET |
| |||
|
|
|
|
| 25 | Function | |
|
|
|
|
|
| ||
3 |
|
|
|
|
| 26 | |
|
|
|
|
| 24.Time Adjusting button | ||
|
|
| ON/OFF |
| 27 | ||
2 |
|
|
|
|
| 28 | Used to adjust the time of |
1 |
|
|
|
|
| ||
|
|
|
|
|
| ||
|
|
|
|
|
| timer and clock | |
|
|
|
|
|
|
|
1.ON/OFF button | 12.Humidifying state display | 25.Reset button | |||
Used to turn on/off unit | 13.Sleep state display |
| |||
|
| When the wire controller | |||
2.Temperature display | 14.Network control display |
| |||
| a p p e a r s a b n o r m a l | ||||
3.Clock display | 15.Working mode display |
|
| ||
|
| condition, use a sharp- | |||
4.Timer ON/OFF display | Working | Auto Cooling Dehumidifying | Heating Fan |
| |
| pointed article to press | ||||
5.Humidity display | mode | operation operation operation | operation operation | ||
Wire |
|
|
| this button to make the | |
6.Air filter cleaning display | controller |
|
|
| wire controller resume |
| 16.Electric heating display |
|
| normal |
26.Air Filter Reset button
Used to set working mode:
17.OperatiAuto, Cooling,modeDehumidifying,button
Heating, Fan
After cleaning the air inlet, press this button, the unit can start to operate
7.Super/Soft operation display 18.Fan speed button 8.Fan speed display
Auto
27.Timer button
Used to set the mode of timer
Low Fan Med Fan High Fan Auto |
9.Auto Swing display 10.Health state display 11.Fresh air state display
19.Swing button
Used to set Auto Swing or
Fixed air sending direction
20.Temperature Setting button
Used to set temperature, temperature range: 16*~30*
28.Lock state display
Note:
This model does not have the following related display and
function * * 10 11 12 28
Calibration of clock
When turning on the unit for the first time, the clock should be calibrated. The method of calibration is:
1.Press ìClockî button, the Clock display ìAMî ìPMî will flash.
2.Press * or * to adjust time. For each press, the time will increase or*decrease 1 minute. If depressing the button, the time will increase or decrease*rapidly.
3.After confirming the time, press ìSetî button, ìAMî or ìPMî will stop flashing, the clock will begin to work.
4