Manuals / Harbor Freight Tools / Household Appliance / Water Heater

Harbor Freight Tools 93762 To Attach The Bandsaw To The Stand, Figure B, See Figure C

Models: 93762

1 29

Download 29 pages 58.01 Kb

Page 10

To Attach The Bandsaw To The Stand:

To Attach The Bandsaw To The Stand:

STAND

(TOP VIEW)

	MOUNTING HOLE
MOUNTING HOLE	MOUNTING HOLE

MOUNTING HOLE	MOUNTING HOLE
	MOUNTING HOLE

SCREW (59)

SPRING WASHER (58)

FLAT WASHER (57)

FIGURE B

1.With additional manpower, and an adequate lifting device, carefully set the Bandsaw on top of the Stand as- sembly, making sure the upper sec- tion of the Stand fits outside the base of the Bandsaw. (See Figure B.)

2.Align the three threaded mounting holes in each end at the base of the Bandsaw with the three mount- ing holes located at each end of the Stand assembly. Then secure the Bandsaw to the Stand assembly, us- ing three Screws (59), three Spring Washers (58), and three Flat Wash- ers (57). (See Figure B.)

To Attach The Stock Stop Assembly:

1.When mounted to the Bandsaw, the adjustable Stock Stop assembly is used to make repetitive cuts of the same length.

HEX BOLT (149)

SOCKET HEAD

SCREW (156)

SHAFT (158)

STOCK

STOP (157)

END VIEW

WITH

HAND WHEEL (171)

IN FOREGROUND

FIGURE C

2.To attach the Stock Stop assembly, slide the Shaft (158) into the mount- ing hole in the Machine Bed (142), and secure the Shaft by tightening the Hex Bolt (149). (See Figure C)

3.Slide the Stock Stop (157) onto the Shaft (158), and secure by tightening the Socket Head Screw (156).

(See Figure C.)

SKU 93762

For technical questions, please call 1-800-444-3353.

Page 10

Image 10

Harbor Freight Tools 93762 To Attach The Bandsaw To The Stand, Figure B, To Attach The Stock Stop Assembly, Figure C

Contents

horizontal/vertical metal cutting bandsaw Set up and Operating InstructionsModel Contents CAUTION, used with the safety Important SAFETY InformationSave This Manual CAUTION, without the safety alertLENGTH NAMEPLATEEXTENSION CORD 100’Manual Before Operating Saw Band Saw Safety WarningsFor Your Own Safety Read Instruction For technical questions, please call20.Use indoors only For technical questions, please callVibration Safety Save these instructionsGrounding Instructions To prevent electric shockOutlets for 2-ProngPlug Double Insulated Tools Toolswith Two Prong Plugs For technical questions, please callUNPACKING SPECIFICATIONSASSEMBLY INSTRUCTIONS To Assemble The StandFIGURE B To Attach The Stock Stop AssemblyTo Attach The Bandsaw To The Stand FIGURE CTo Attach The Pulley Cover To Install The V-BeltSee Figures E and F To Adjust The Cutting Speed 2. See Figure ETo Convert The Bandsaw For Vertical Use FIGURE GSee Figures E, F, and G FIGURE HBolt. See Figures I and J See FigureFIGURE J For technical questions, please callTo Use The Vise OPERATING INSTRUCTIONSTo Use The Quick Vise Adjustment For An Angle Cut See Figure HAdjusting The Blade Tracking To Adjust The Stock StopSee Figure M Adjusting The Blade Guide Bearings FIGURE MSee Figure P See Figure O Adjusting The Blade TensionSee Figure H FIGURE OFIGURE Q Adjusting The Feed RateAdjusting The Blade Guide Brackets See Figure QSee Figure S FIGURE SSee Figure S See Figure SSee Figure S See Figure SSee Figure S See Figure TSee Figure T For technical questions, please callSee Figure U INSPECTION, MAINTENANCE AND CLEANINGDo not use damaged equipment FIGURE USee Figure See Figure USee Figure U See Figure FSee Figure FIGURE WFigure W For technical questions, please callTROUBLESHOOTING For technical questions, please callFor technical questions, please call PARTS LISTREV 09f PARTS LIST CONT For technical questions, please callPLEASE READ THE FOLLOWING CAREFULLY PARTS LIST CONTSKU 93762 For technical questions, please call ASSEMBLY DIAGRAM For technical questions, please callLimited 1 year / 90 Day warranty For technical questions, please call