Harman-Kardon AVR4500 owner manual Advanced Features, Display Brightness, Turn On Volume Level

Advanced Features

The AVR 4500 is equipped with a number of advanced features that add extra flexibility to the unit’s operation. While it is not necessary to use these features to operate the unit, they pro- vide additional options that you may wish to use.

Display Brightness

The AVR 4500’s front panel Main Information Display ˜ is set at a default brightness level that is sufficient for viewing in a normally lit room. However, in some home theater installa- tions, you may wish to occasionally lower the brightness of the display, or turn it off completely.

To change the display brightness setting for a specific listening session, you will need to make an adjustment in the ADVANCED menu. To start the adjustment, press the OSD button L to bring the MASTER MENU to the screen. Press the ⁄ Button Dtwice, until the on-screen › cursor is next to the ADVANCED line. Press the Set Button F to enter the ADVANCED menu (Figure 11).

*	A D V A N C E D		*
V F D	:	F U L L	H A L F O F F

V O L U M E D E F A U L T : O F F O N

D E F A U L T V O L S E T :

S E M I O S D : O F F O N

S E M I	O S D	T I M E	O U T :	3 5
F U L L	O S D	T I M E	O U T : 2 0 5

R E T U R N T O M A S T E R M E N U

Figure 11

To change the brightness setting, at the ADVANCED menu, make certain that the on-screen › cursor is next to the VFD line,

and press the › Button until the desired brightness level is highlighted in the video dis- play. When FULL is highlighted, the display is at its normal brightness. When HALF is high- lighted, the display is at half the normal bright- ness level. When OFF is highlighted, all of the indicators in the Main Information Display

˜will go dark. Note, however, that the green LEDs for the Input Indicators ˆ and the Surround Mode Indicators ˘, as well as for the Power Indicator 3, will always remain lit to remind you that the unit is turned on.

If you wish to make other adjustments in the menu, press the ⁄/¤ Buttons Duntil the on- screen › cursor is next to the desired setting or the RETURN TO MENU line and press the Set button F. If you have no other adjust- ments to make, press the OSD Button Lto exit the menu system.

The display brightness may also be changed by pressing and holding the Set button @ on the front for three seconds until the message in the Main Information Display Y reads VFD FULL. Within five seconds, press the front panel Selector buttons 7$ until the desired brightness display level is shown. At that point, press the Set button @ again to enter the setting.

Once the desired brightness level is selected, it will remain in effect until it is changed again or until the unit is turned off.

Turn On Volume Level

As is the case with most audio/video receivers, when the AVR 4500 is turned on, it will always return to the volume setting in effect when the unit was turned off. However, you may prefer to always have the AVR 4500 turn on at a specific setting, regardless of what was last in use when the unit was turned off. To change the default condition so that the same volume level is always used at turn-on, you will need to make an adjustment in the ADVANCED menu. To start the adjustment, press the OSD button L to bring the MASTER MENU (Figure 1) to the screen. Press the ⁄ button Dtwice, until the on-screen › cursor is next to the ADVANCED line. Press the Set button F to enter the ADVANCED menu (Figure 11).

At the ADVANCED menu make certain that the on-screen › cursor is next to the VOLUME DEFAULT line by pressing the ⁄/¤ buttons Das needed. Next, press the ›

button so that the word ON is highlighted in the video display. Next, press the ¤ button Donce so that the on-screen › cursor is next to the DEFAULT VOL SET line. To set the desired turn-on volume, press the ‹/ › but- tons E or hold them pressed until the desired volume level is shown on the DEFAULT VOL SET line. Note that this setting may NOT be made with the regular volume controls.

NOTE: Since the setting for the turn-on volume cannot be heard while the setting is being made, you may wish to determine the setting before making the adjustment. To do this, listen to any source and adjust the volume to the desired level using the regular volume controls î. When the desired volume level to be used at turn-on is reached, make a note of the setting as it appears in the lower third of the video screen or in the Main Information Display Y. A typical volume level will appear as a negative number such as -25dB. When making the adjust-

ment, use the ‹/› buttons E	to enter this
setting.

Unlike some of the other adjustments in this menu, the turn-on volume default will remain in effect even when the unit is turned off completely, unless it is changed or turned off in this menu.

If you wish to make other adjustments in the menu, press the ⁄/¤ Buttons Duntil the on- screen › cursor is next to the desired setting or the RETURN TO MENU line and press the Set button F. If you have no other adjust- ments to make, press the OSD Button Lto exit the menu system.

ADVANCED FEATURES 37