AVR80 manual 11/01/98 13:01 Side 4
ENGLISH
Front Panel Controls
4
1Information display: This display delivers messages and status indications to help you operate the receiver. Refer to the separate diagram for a complete explanation of the FL display.
2Remote Sensor Window: The sensor behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it unless an external remote sensor is installed.
3AM/FM Tuner Mode Selection: Press this button once to select the tuner. Press it again to switch between FM, MW and LW.
4CD: Press this button to select the CD player.
5Tape1/Monitor: Press this button to select Tape One as the input source. A red LED above the button will illuminate to indicate that the Tape Monitor has been selected.
6Tape 2: Press this button to select Tape 2.
7Video Sources: Press any of these buttons to select a video input source.
8Aux: Press this button to select the source connected to the front panel Aux jacks.
9Multiroom Audio Select: Press this button to turn on the feed to the remote zone. The remote zone will stay on after the main power switch is turned off until it is switched off by the remote room control or by pressing this button again.
)Display: Press this button to
turn off the front panel FL display. The DISP indicator will illuminate
to remind you that the unit is still turned on.
!OSD (On Screen Display): Press the button briefly to display a system status report on your video screen. Press and hold the button to change the video standard.
@Delay: Press this button to increase the delay to the rear (surround) channels.
#Mode: Press these buttons to scroll up Ú or down Û through the list of available surround modes.
$
%
^Tune: Press these buttons to manually or automatically scan up Ú or down Û through the FM, LW or AM bands.
& Mute: Press this button to cut the output to the speakers. Press it again to return to the previous volume level.
* Volume Control: Turn the knob clockwise to increase volume, counterclockwise to decrease the volume. Note that approximately two revolutions of the knob are required to go from no output to maximum volume.
(Power: Press this button to turn the unit on or off.
NOTE: When the Power Switch is in the “OFF” position, the unit is in a “Standby” condition and is NOT disconnected from the AC mains supply.
îHeadphone Jack: Plug standard stereo headphones into this jack for private listening.
NOTE: When the headphones are in use the output to the speakers is muted and the surround mode is automatically switched to STEREO. When the headphones are removed from the jack, sound to the speakers is restored and the unit returns to the previous sound mode.
ï 6 Channel Direct: Press this button to select the output of an external multichannel audio adapter.
ðTape 1 Copy: Press this button to select the in record source for the recorder connected to Tape1. The first press will select the source currently being listened to. Press again to select the source in the following order: Tuner◊CD◊Tape2◊Source.
ñ VCR1 Copy: Press this button to select the record source to the recorder connected to VCR1. The first press selects the input currently being viewed. Press the button again to select the input in the
following order:
TV◊LD◊VCR2◊AUX◊Source
òMemo: The memo button is used to enter stations to the tuner’s preset memory in either the manual or automatic modes. It is also used in clearing the memory and entering the sleep timer period.
óClear: The clear button is used to cancel tuning, memory input or when clearing the unit’s memories.
ôFM Mode: Press this button
to select the receiving mode for FM stations (Stereo/Mono/Auto).
õRDS Display: When a station transmitting RDS data is tuned, press this button to view the tuning frequency.
öRDS AF: The button is used to search for stations transmitting a specific program that may offer better reception than the currently tuned station.
÷ RDS PTY: Press this button to view the programme type (PTY) when an RDS station is tuned. It is also used to initiate a search for RDS stations transmitting a specific programme type.
øBass: This knob adjusts the tone of low frequency sounds. Turn it to the right to boost bass frequencies or to the left to cut bass frequencies.
ùTreble: This knob adjusts
the tone of high frequency sounds. Turn to it the right to boost high frequencies or to the left to cut high frequencies.
üBalance: This knob adjusts the balance between the front left and right speakers.
ýFront Panel Inputs: Audio or Video sources connected to these jacks may be selected by pressing the Aux button 8.
