FRONT-PANEL CONTROLS
8 Surround Mode Selector: Press this button to select from among the available surround mode options for the mode group selected. The specific modes will vary based on the number of speakers available, the mode group and if the input source is digital or analog. For example, press the Surround Mode Group Selector 7 to select a main mode grouping such as Dolby or Logic 7, and then press this button to see the specific mode choices available. For more information on mode selection, see page 22.
9Tuning Selector: Press the left side of the button to tune
will indicate AUTO TUNED. When an FM Stereo station is tuned, the display will read
AUTO ST TUNED.
To switch back and forth between the Auto and Manual tuning modes, press the Tuner Mode Selector &.
)‹/› Buttons: When configuring the AVR 135’s settings, use these buttons to select from the available choices.
!Tuner Band Selector: Press this button to turn the AVR on and to select the Tuner as the input. Press it again to switch between the AM and FM frequency bands. (See page 26 for more information on the tuner.)
@Set Button: When making choices during the setup and configuration process, press this button
to enter the desired setting into the AVR 135’s memory.
#Digital Input Selector: Press this button to
select one of the digital inputs or the analog input for any source. (See pages
$ Preset Stations Selector: Press this button to scroll up or down through the list of stations that have been entered into the preset memory. (See page 27 for more information on tuner presets.)
%Delay Adjust Selector: Press this button to begin the steps required to enter delay settings. (See pages
^Input Source Selector: Press this button to change the input by scrolling up or down through the list of Input Indicators ı.
&Tuner Mode Selector: Press this button to select Auto or Manual tuning. When the button is pressed so that the AUTO appears in the Lower Display Line ¯, the tuner will search for the next station with an acceptable signal when the Tuning Selector 9u is pressed. When the button is pressed so that
MANUAL appears in the Lower Display Line ¯, each press of the Tuning Selector 9uwill increase the frequency. This button may also be used to switch between Stereo and Mono modes for FM radio reception. When weak reception is encountered, press the button so that MANUAL appears in the Lower Display Line ¯and on the
*Optical 3 Digital Audio Input: Connect the optical digital audio output of an audio or video product to this jack. When the input is not in use, be certain to keep the plastic cap installed to avoid dust contamination that might degrade future performance.
( Coaxial 3 Digital Audio Input: This jack is used for connection to the output of portable audio devices, video game consoles or other products that have a coax digital audio jack.
ÓVideo 3 Video Input Jacks: These jacks may be used for temporary connection to the composite or
ÔVideo 3 Audio Input Jacks: These audio jacks may be used for temporary connection to video games or portable audio/video products such as camcorders and portable audio players.
Bass Control: Turn this control to modify the low- frequency output of the left/right channels by as much as ±10dB.
ÒBalance Control: Turn this control to change the relative volume for the front left/right channels.
NOTE: For proper operation of the surround modes this control should be at the midpoint or “12 o’clock” position.
ÚTreble Control: Turn this control to modify the high frequency output of the left/right channels by as much as ±10dB.
ÛChannel Adjust Selector: Press this button to begin the process of trimming the channel output lev- els using an external audio source. (For more informa- tion on output level trim adjustment, see page 27.)
ÙVolume Control: Turn this knob clockwise to increase the volume, counterclockwise to decrease the
volume. If the AVR 135 is muted, adjusting the Volume Control Ù
38 will automatically release the unit from the silenced condition.
ıInput Indicators: The current selected source will appear as one of these indicators. Note that when the unit is turned on, the entire list of available modes will light briefly, and then revert to normal operation with only the active mode indicator illuminated.
ˆSpeaker/Channel Input Indicators: These indi- cators are multipurpose, indicating both the speaker type selected for each channel and the incoming data- signal configuration. The left, center, right, right surround and left surround speaker indicators are composed of three boxes, while the subwoofer is a single box. The center box lights when a “small” speaker is selected, and the two outer boxes light when “large” speakers are selected. When none of the boxes are lit for the center, surround or subwoofer channels, no speaker has been assigned that position. (See page 17 for more informa- tion on configuring speakers.) The letters inside each box displays the active input channels. For standard analog inputs, only the L and R will light, indicating a stereo input. For a digital source, the indicators will light to display the channels being received at the digital input. When the letters flash, the digital input has been interrupted. (See page 25 for more information on the Channel Indicators.)
˜Upper Display Line: Depending on the unit’s sta- tus, a variety of messages will appear here. In normal operation, this line will show current input source and which analog or digital input is in use. When the tuner is the input, this line will identify the station as AM or FM and show the frequency and preset number, if any.
¯Lower Display Line: Depending on the unit’s sta- tus, a variety of messages will appear here. In normal operation, the current surround mode will show here.
˘Surround Mode Indicators: The current selected surround mode will appear as one of these indicators. Note that when the unit is turned on, the entire list of available modes will light briefly, and then revert to normal operation with only the active mode indicator illuminated.
¸Remote Sensor Window: The sensor behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it.
6
