Harman-Kardon AVR 135 owner manual FRONT-PANEL Controls, # %

FRONT-PANEL CONTROLS

¸	˘	¯	˜	ˆ	ı	Ù	Û Ú
AVR 135
	DIGITAL	LOGIC 7			VID 1	DVD
	PRO LOGIC				VID 2	CD
	3 STEREO	DSP			VID 3	FMAM
		5 CH. STEREO				TAPE
		SURR. OFF				6 8 CH

1 3	5	7		9 !# %	&	(		Ô Ò
2	4	6	8	) @)$ ^		*	Ó	￿

NOTE: To make it easier to follow the instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section for this product at www.harmankardon.com.

1 Main Power Switch	@ Set Button	Ò Balance Control
2 Power Indicator	# Digital Input Selector	Ú Treble Control
3 Standby/On Switch	$ Preset Station Selector	Û Channel Adjust Selector
4 Headphone Jack	% Delay Adjust Selector	ÙVolume Control
5 Tone Mode	^ Input Source Selector	ı Input Indicators
6 Speaker Selector	& Tuner Mode Selector	ˆ Speaker/Channel Input Indicators
7 Surround Mode Group Selector	* Optical 3 Digital Audio Input	˜ Upper Display Line
8 Surround Mode Selector	( Coaxial 3 Digital Audio Input	¯ Lower Display Line
9 Tuning Selector	Ó Video 3 Video Input Jacks	˘ Surround Mode Indicators
)‹/› Buttons	Ô Video 3 Audio Input Jacks	¸ Remote Sensor Window
! Tuner Band Selector	￿ Bass Control

1 Main Power Switch: Press this button to apply power to the AVR 135. When the switch is pressed in, the unit is in a Standby mode, as indicated by the amber LED 2 above the Standby/On Switch 3. This button MUST be pressed in to operate the unit. To turn the unit off and prevent the use of the remote control, this switch should be pressed until it pops out from the front panel and the word “OFF” is seen at the top of the switch.

NOTE: This switch is normally left in the “ON” position.

2 Power Indicator: This LED lights amber when the unit is in the Standby mode to signal that the AVR is ready to be turned on. When the unit is in operation, the indicator is blue.

3 Standby/On Switch: When the Main Power Switch 1 is “ON,” press this button to turn on the AVR 135; press it again to turn the unit off. The Power Indicator 3 turns blue when the unit is on.

4Headphone Jack: This jack may be used to listen to the AVR 135’s output through a pair of headphones. The speakers will automatically be turned off when the headphone jack is in use.

5Tone Mode: Pressing this button enables or dis- ables the Bass and Treble tone controls. When the but- ton is pressed so that TONE IN appears in the Lower Display Line ¯, the Bass ￿ and Treble

Úcontrols may be used to adjust the output signals. When the button is pressed once or twice so that the words TONE OUT appear in the Lower Display Line ¯, the output signal will be “flat,” no matter how the actual Bass and Treble Controls ￿Úare adjusted.

6 Speaker Selector: Press this button to begin the process of configuring the unit to match the type of speakers used in your listening room. (See pages 17–19 for more information on speaker setup and configuration.)

7 Surround Mode Group Selector: Press this but- ton to select the top-level group of surround modes. Each press of the button will select the current or last used mode in each of the surround mode groups (e.g., Dolby, DTS, DTS Neo:6, Logic 7, DSP, Stereo). When the button is pressed so that the name of the surround mode group appears in the on-screen display and in the Lower Display Line ¯, press the Surround Mode Selector 8 to cycle through the individual modes available. For example, press this but- ton to select Dolby modes, and then press the Surround Mode Selector 8 to choose from the various mode options.

FRONT-PANEL CONTROLS 5