Installation and Connections |
|
|
| ENGLISH |
• If you use only normal video devices the TV | Figure 1: |
| Yellow | |
monitor needs an adapter from 3 RCA plugs to |
|
| Black |
|
|
|
|
| |
Scart (fig. 3) only. If also |
|
|
| |
used an adapter from 2 |
| Red |
| |
for playback; |
|
| ||
to Scart is needed additionally (fig. 6), | signal flow: |
|
|
|
connected to the SCART input on your TV that | SCART ’ Cinch |
|
|
|
is provided for |
|
| Black |
|
|
|
|
| |
Note that only the video plugs (the "yellow" |
|
| Red |
|
cinch plug in fig. 3 and the |
|
| Blue1 |
|
fig. 6) must be connected to the TV Monitor |
|
| Yellow |
|
Output , and the volume on the TV must be | Figure 2: |
|
| |
| Green1 |
| ||
reduced to minimum. |
|
| ||
Important Note for Adapter Cables: | for record and playback; |
| White |
|
signal flow: |
|
|
| |
If the cinch connectors of the adapter you’ll use | SCART ÷ Cinch |
|
|
|
are labeled, connect the Audio and Video ”In” |
| Black |
|
|
plugs with the corresponding Audio and Video | Figure 3: | Yellow |
|
|
”In” jacks on the AVR (and with a VCR connect |
|
| ||
Red |
|
| ||
the ”Out” plugs to the ”Out” jacks on the VCR). | playback; |
|
| |
|
|
| ||
Note that with some adapter types it may be just | signal flow: |
|
|
|
turned around: If no signal is audible/visible when | Cinch ’ SCART |
|
|
|
|
|
|
| |
the VCR is playing connect the “Out” plugs to the |
|
| Red |
|
”In” jacks on the AVR and turned around. If the | Figure 4: |
| Black |
|
adapter plugs are not labeled in that way, pay |
|
|
| |
attention to the signal flow directions as shown | for playback; |
|
| |
in the diagrams above and in the instruction | signal flow: |
|
|
|
attached to the adapter. If uncertain, don’t hesi- | SCART ’ Cinch |
|
|
|
|
|
|
| |
tate to consult your dealer. |
|
| Black |
|
Important Notes for |
|
| Red |
|
Only the |
|
| Blue1 |
|
be connected to the AVR, NOT both, normal video | Figure 5: |
| Yellow |
|
and |
|
|
| |
|
|
| ||
below). |
|
|
| |
for record and playback; |
|
| ||
When both connections are made, only the | signal flow: |
|
| |
SCART ÷ Cinch |
|
| ||
|
|
| ||
Important Note for the Use of | Figure 6: | Red |
|
|
| Black |
|
| |
When video sources are connected to the TV |
|
|
| |
for playback; |
|
|
| |
directly with a SCART cable, specific control |
|
| ||
signal flow: |
|
| ||
signals apart from Audio/Video signals will be fed |
|
|
| |
Cinch ’ SCART |
|
|
| |
to the TV. These specific signals are: With all video | 1 Also other colours possible, e.g. brown and grey. |
| ||
|
| |||
sources, the signal for automatic input selection |
|
|
|
|
that switches the TV automatically to the appro- |
|
|
|
|
priate input as soon as the video source is start- |
|
|
|
|
ed. And with DVD players, the signals automati- | AVR only when no separate sync signal is needed | NOTE: Many audio and video products go into a |
| |
cally turning the TV to 4:3/16:9 format (with 16:9 | (see last ”Video Connection Note” on page 14). | Standby mode when they are used with switched |
| |
TVs or with 4:3 TVs with selectable 16:9 format) |
|
| outlets, and cannot be fully turned on using the |
|
and turning the RGB video decoder of the TV on | Power Connections |
| outlet alone without a remote control command. |
|
or off, depending on the DVD player´s setting. |
| Once the power cord is connected, you are |
| |
With any adapter cable, these control signals will | AC Power Connections |
|
| |
| almost ready to enjoy the AVR 155’s incredible |
| ||
be lost and the appropriate setting of the TV must |
|
| ||
This unit is equipped with one accessory AC out- |
| |||
power and fidelity! |
| |||
be made manually. |
| |||
let. It may be used to power Accessory devices, |
| |||
|
| |||
|
|
| ||
Note for RGB signal with SCART: | but it should not be used with |
|
| |
equipment such as power amplifiers. The total |
|
| ||
If you use a unit providing RGB signals on a |
|
| ||
power draw to the Switched Outlet must |
|
| ||
SCART output (as e.g. most DVD players do) and |
|
| ||
not exceed 50 watts. |
|
|
| |
you want to use that RGB signal, this SCART out- |
|
|
| |
|
|
|
| |
put must be connected directly to your TV. | The Switched outlet will receive power only |
|
| |
Although the AVR can switch | when the unit is on completely. This is recom- |
|
| |
signals (like component signals Y/Pb/Pr), most TVs | mended for devices that have no power switch |
|
| |
need separate sync signals for RGB (also with | or a mechanical power switch that may be left in |
|
| |
SCART) that cannot be switched and provided by | the “ON” position. |
|
|
|
the AVR. RGB signals can be pathed through the |
|
|
|
|
|
|
| INSTALLATION AND CONNECTIONS 15 |
|