OPERATION
Basic Operation
Once you have completed the initial setup and configu- ration of the AVR 230, it is simple to operate and enjoy. The following instructions will help you maximize the enjoyment of your new receiver:
Turning the AVR 230 On or Off
•When using the AVR 230 for the first time, you must first press the Main Power Switch 1 on the front panel to turn the unit on. This places the unit in a
Standby mode, as indicated by the amber color of the Power Indicator 2. Once the unit is in Standby, you
may begin a listening session by pressing the Standby/On Switch 3 on the front panel, or the Power On Button d or AVR Selector f on the remote. The Power Indicator 2 will turn blue. This will turn the unit on and return it to the input source that was last used. The unit may also be turned on from Standby by pressing any of the Input Selector Buttons eg on the remote or the Input Source Selector Button ^ on the front panel.
NOTE: After pressing one of the Input Selector Buttons eg to turn the unit on, press the AVR Selector f to set the remote control to the AVR 230 functions.
To turn the unit off at the end of a listening session, simply press the Standby/On Switch 3 on the front panel or the Power Off Button a on the remote. Power will be shut off to any equipment plugged into the
When the remote is used to turn the unit “off” it is actually placing the system in a Standby mode, as indi- cated by the amber color of the Power Indicator 2.
•To program the AVR 230 for automatic
|
|
| 90 | 80 | 70 | 60 | 50 |
| ||||
|
|
| min |
| min |
| min |
| min |
| min |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 40 | 30 | 20 | 10 | OFF | |||||
|
|
| min |
| min |
| min |
| min |
| ||
|
|
|
|
| ||||||||
The sleep time will be displayed in the Lower Display Line ¯ and it will count down until the time has elapsed.
When the programmed sleep time has elapsed, the unit will automatically turn off. The
When you will be away from home for an extended period of time it is always a good idea to completely turn the unit off with the
NOTE: All preset memories are lost if the unit is left turned off by using the Main Power Switch 1 for more than four weeks.
Source Selection
•To select a source, press any of the Input Selector Buttons eg 41 on the remote.
•The input source may also be changed by pressing the
•As the input is changed, the AVR 230 will automati- cally switch to the digital input (if selected), surround mode, output levels and night mode status as well as any speaker configuration or crossover settings established by using the INDEPENDENT Bass Management setting, that were entered during the configuration process for that source.
•The
•As the input source is changed, the new input name will appear momentarily as an
•When an audio source is selected, the last video input
used remains routed to the Video 1/Video 2 Video and
•There are two input choices available for use with sources such as a
the way your system and source equipment are configured:
■6 CH DIRECT should be used when the SBR and SBL inputs are NOT in use and the input source device has its own internal bass management system. This input passes the input from the source directly through to the volume
control without any analog to digital conversion and it mutes the unused input jacks to prevent unwanted noise from interfering with system per- formance.
■8 CH DIRECT should be used when an input is connected to all eight
Volume Control
•Adjust the volume to a comfortable level using the
•To temporarily silence all speaker outputs, press the Mute Button 42 . This will interrupt the output to all speakers and the headphone jack, but it will not affect any recording or dubbing that may be in progress. When the system is muted, the word MUTE will flash in the Lower Display Line ¯. Press the Mute Button 42 again to return to normal operation.
•You may adjust the bass and treble tone controls at any point during a listening session by simply turning the Bass Control or Treble Control
Ú until the desired setting is achieved. You may also totally remove the tone controls from the circuit so that the output is “flat” at any time by pressing the Tone Mode Button 5 and then pressing the ‹/› Button ) so that TONE OFF appears in the
•For private listening, plug the 1/4" stereo phone
plug from a pair of stereo headphones into the
Surround Mode Selection
One of the most important features of the AVR 230 is its ability to reproduce a full multichannel surround sound field from digital sources, analog matrix
Selection of a surround mode is based on personal taste, as well as the type of program source material
