5. With the help of a second person, carefully tip | 5 |
|
|
|
|
|
|
|
the treadmill onto its right side. Partially fold the |
|
| B |
|
|
|
| |
Frame (48) so the treadmill is more stable; do |
| A |
|
|
|
|
| |
not fully fold the Frame yet. |
|
|
|
|
|
|
| |
Remove and discard the two indicated bolts (A) |
|
|
|
|
|
|
|
|
and the shipping bracket (B). |
|
|
|
|
|
| 48 |
|
Attach a Base Foot (81) to the Base (85) in the |
| 81 |
|
|
|
| 4 | |
location shown with a Base Foot Spacer (104) | 2 |
|
|
|
|
| ||
and an M4.2 x 25mm Tek Screw (2). Then, at- |
|
|
|
|
|
|
| |
tach a Base Foot (81) in the location shown with |
| 85 |
|
| 104 |
|
|
|
only an M4.2 x 25mm Tek Screw (2). |
|
|
|
| 86 |
| ||
Remove the M10 Nut (33), the M10 x 50mm |
|
|
|
| 2 | 81 | C | |
Bolt (4), and the shipping bracket (C) from the |
|
|
|
|
| |||
Base (85). Attach a Wheel (86) with the Bolt and |
|
|
|
|
|
| 33 |
|
the Nut that you just removed. Do not over- |
|
|
|
|
|
|
| |
tighten the Nut; the Wheel must turn freely. |
|
|
|
|
|
|
|
|
Discard the shipping bracket. |
|
|
|
|
|
|
|
|
6. Hold a Bolt Spacer (79) inside the lower end of | 6 |
|
|
|
|
|
|
|
the Left Upright (73). Insert an M10 x 96mm Bolt |
|
|
|
|
|
| 73 | |
(5) with an M10 Star Washer (8) into the Left |
|
|
| 5 |
|
|
| |
Upright and the Bolt Spacer. Repeat this step |
|
|
|
|
|
|
| |
with a second Bolt Spacer (79), M10 x 96mm |
|
|
| 8 |
|
|
|
|
Bolt (5), and M10 Star Washer (8). |
|
|
|
| 83 |
|
|
|
Orient the Left Upright (73) and the Left Upright |
|
|
|
|
|
|
| |
Spacer (83) as shown. Hold the Left Upright |
|
|
|
|
|
|
|
|
Spacer and the Left Upright against the Base | 82 | 79 |
|
|
|
|
| |
(85). Tighten the M10 x 96mm Bolts (5) until the |
|
|
|
|
| |||
heads of the Bolts touch the Left Upright; do not |
|
|
| 85 |
|
|
|
|
fully tighten the Bolts yet. |
|
|
|
|
|
|
| |
Press a Base Cap (82) into the Base (85). With |
|
|
|
|
|
|
|
|
the help of a second person, tip the treadmill so |
|
|
|
|
|
|
|
|
that the Base is flat on the floor. |
|
|
|
|
|
|
|
|
7. Set the Console (87) face down on a soft sur- | 7 |
|
|
|
|
|
|
|
face to avoid scratching the Console. Remove |
|
|
|
|
|
|
| |
the six M4.2 x 19mm Screws (1) and lift off the |
|
|
|
|
| 1 |
| |
Pulse Support (109). Save all six Screws and |
|
|
|
|
|
| ||
the Pulse Support for step 9. |
|
|
| 1 |
|
|
|
|
|
| 1 |
| 87 |
|
|
| |
|
| 109 |
|
|
|
| ||
| 9 |
|
|
|
|
|
|
|