Hearth and Home Technologies 5100-I installation instructions Brick Replacement Instructions

R

5100-I WOOD INSERT

BRICK REPLACEMENT INSTRUCTIONS

FIREBOX BRICK SET, PART 832-1970

The firebox of your Quadra-Fire 5100-I Insert is lined with high quality firebrick which has exceptional insulat- ing properties. There is no need for a grate, simply build a fire on the firebox of your insert.

Nbr	Brick Size	Qty in Set
1	9 x 4-1/2 x 1-1/4”	14
2	9 x 1-3/4 x 1-1/4”	4
3	8-1/2 x 2-1/4 x 1-1/4”	4
4	8 x 4-1/2 x 1-1/4”	1
5	8 x 4 x 1-1/4” (chamfered) 1
6	8-1/2 x 2 x 1-1/4”	2
7	7-1/2 x 4 x1-1/4”	2
8	see drawing	2
9	see drawing	2
10	see drawing	2

1.Be certain coals are completely cold. Remove all old brick and ash from unit and vacuum out firebox.

2.Remove new brick set from box and lay out to diagram as shown.

3.Lay bottom bricks in unit.

4.Install rear bricks on the top of the bottom bricks. Slide top of bricks under clip on back of firebox wall and push bottom of brick back.

5.Install side bricks. Slide top of brick under clips on side of firebox and push the bottom of the brick until it is flush with the side of the unit.

Use Part #832-0550 when ordering individual brick and provide brick dimension or copy this page and mark the desired brick and take it to your authorized dealer.

				1
		/4
		-3
		6
		8	2	3
	2
	-1/
	7			1
		2	1
		-1/
7		3
		3/4	1	1
3-1/8		8-1/2		1
9 3-3/4 5-5/8		10		6
2-3/4
3-3/4				1
	3/4	3-3/4
		4-1/2

4

1

5

3

1

2

1

1

2

1

		6
			-
			3
			/
			4
			8	7
2				-
					1/
		3			2
		-
			1/
1			2			7
			3/4
	8-1/2		10				3-1/8
				5-5/8		3-3/4	9
6							2-3/4
			3-3/4	3/4			3-3/4
			4-1/2

BAFFLE BRICK REMOVAL & INSTALLATION

BAFFLE BRICK SET, PART 832-1940

NOTE: The baffle is made of pumice firebrick supported by stainless steel brackets and covered with a 1/2” ceramic blanket which contacts the firebox on the sides and the back.

1.Remove the manifold tube located second from the rear of the firebox.

2.Place the two baffle bricks located second from the rear up onto the rear baffle bricks.

3.Slide remaining baffle brick, one at a time, to the resulting open- ing. Once brick is over opening, lift one side up toward stove top and drop the other side down free from middle baffle support and into the firebox.

4.Ceramic blanket can be removed out the front of the stove, or dropped out through the opening to the rear of the stove.

5.Reinstall ceramic blanket and baffle brick in reverse order. Make sure that the manifold tube is secured in place and that the ceramic blanket is resting flat on the top of the baffle and is in contact with the firebox sides and back.

1	1
1	1
1	1
1	1

Stainless Steel Supporting Brackets

Size of all 8 baffle bricks: 9 x 4-1/2 x 1-1/4”

January 30, 2004 250-1960 Rev B Page 21