Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies BE-36-CIPI manual Venting with Four 90 elbows

Models: BE-36-C BE-36-CIPI

1 37

Download 37 pages 30.79 Kb

Page 22

VENTING WITH FOUR (4) 90° ELBOWS

NATURAL AND PROPANE GAS

V (MIN.)	H (MAX.)	V1 (MIN.)	H1 (MAX.)	V2 (MIN.)
2' (609mm)	5' (1.52m)	5' (1.52m)	5' (1.52m)	4.5' (1.37m)

V + V1 + V2 + H + H1 MAX. = 40' (12.2m)

NOTE: There MUST be a 25% reduc- tion in total H when using flex vent except when using the simple up and out installation (see Figure 7).

H1

V2

	Use SL D-Series	V1
	components only.	V1
	components only.

H

V

Figure 16. Venting with Four 90° elbows

22	Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. R • 2/05

Image 22

Hearth and Home Technologies BE-36-CIPI manual Venting with Four 90 elbows

Contents

Installers Guide What to do if you smell gasSafety and Warning Information Table of Contents Log Set Assembly BE-36-C, BE-36-CIPICommon Parts / Pièces communes Valve Assembly Intermittent Pilot IgnitionBE-36-C Standing Pilot IgnitionAppliance Certification High Altitude InstallationsInstallation Codes CertificationIntroducing the Hearth & Home Technologies Gas Fireplaces Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of model BE-36-C Locating the Fireplace Constructing the Fireplace ChaseClearance Requirements Framing the Fireplace for DVP-Series and SL D-Series Pipe C D* EInch inner pipe / 6 5/8-inch outer pipe 47 3/434.93mm AT Each Joint Vent System Approvals Installing the Vent SystemIdentifying Vent Components Vent System ComponentsUse SL D-Series components only Flex VentStraight UP Vertical Venting Use DVP-Series Components onlyVenting with One 90 Elbow Use SL D-Series Use DVP-Series Venting with Two 90 ElbowsUse SL D-Series components only Venting with Three 90 elbows + H1 MAX. = 16 4.8m + H + V1 + H1 MAX. = 40 12.2m Venting with Four 90 elbows Go to Install Firestops DVP Series Venting OnlySL-D and SL-Flex Series Venting Only Attach the First Vent Component to the Starting CollarsDVP, SL-D and SL-Flex Series Venting Hole and Vent PipeFor DVP Venting Only Vent TerminationSL-Series Venting Only For All VentingVent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Securing of a Fireplace Positioning, Leveling, and Securing the FireplaceGas Control System Standing Pilot Ignition SystemGas Pressure Requirements Gas Supply LinePressure Natural Gas Propane Wiring the Fireplace Valve will be DestroyedRemote Wiring Diagram IPI Intermittent Pilot Ignition IPI Wiring Diagram Finishing Installing Trim, Logs, and Ember MaterialLET/OUTLET Grilles in ANY Manner Glass Specifications Tempered Placing the Ember MaterialBefore Lighting the Fireplace After the InstallationDouble-check for faulty components Lighting the FireplaceFireplace Maintenance Important Turn OFF the GAS Before Servicing Your Fireplace