PILOT

PIEZO

THERMOCOUPLE

 

WHITE

 

RED

 

VALVE

 

THERMOSTAT

 

WIRE ASSEMBLY

 

Figure 31.

 

Standing Pilot

 

Ignition Wiring Diagram

 

Step 8. Wiring the Fireplace

NOTE: Electrical wiring must be installed by a licensed electrician.

CAUTION: DISCONNECT REMOTE CONTROLS IF AB- SENT FOR EXTENDED TIME PERIODS. THIS WILL PRE- VENT ACCIDENTAL FIREPLACE OPERATION.

For Standing Pilot Ignition Wiring

Appliance Requirements

•This appliance DOES NOT require 110-120 VAC to operate.

!WARNING: DO NOT CONNECT 110-120 VAC TO THE GAS CONTROL VALVE OR WALL SWITCH OR THE APPLIANCE WILL MALFUNCTION AND THE VALVE WILL BE DESTROYED.

Optional Accessories

Optional fan and remote control kits require that 110-120 VAC be wired to the factory installed junction box before the fireplace is permanently installed.

Wall Switch

Position the wall switch in the desired position on a wall. Run a maximum of 25 feet (7.8 m) or less length of 18 A.W.G. minimum wire and connect it to the fireplace ON/ OFF switch pigtails.

CAUTION: LABEL ALL WIRES PRIOR TO DISCONNEC- TION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPERAND DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING.

Intermittent Pilot Ignition (IPI) Wiring

Appliance Requirements

This appliance requires that 110-120 VAC be wired to the factory installed junction box. Maintain correct polarity when wiring the junction box.

!WARNING: DO NOT CONNECT 110-120 VAC TO THE GAS CONTROL VALVE OR THE AP- PLIANCE WILL MALFUNCTION AND THE VALVE WILL BE DESTROYED.

Operation using Battery Power

This fireplace has an optional battery operation. The sys- tem is fully functional with the use of two “D” size batteries without ordinary 110-120 VAC power.

Wiring to the battery pack should be left disconnected in order to conserve battery life. In the case of a loss of power, simply connect red and black wire leads to activate battery power (connect red to red, black to black). The fireplace can be used as necessary. Once power (110 VAC) is re- stored, disconnect red and black wire leads to extend bat- tery life.

Installing the Batteries

Remove battery pack which is secured in place adjacent to gas control valve (secured with velcro strip). Orient two “D” size batteries per the diagram on battery pack. Re-install battery pack in the same location.

Wall Switch (Required)

A wall switch must be installed for this fireplace. This will allow the unit to operate with 110-120 VAC power or battery operation.

Position the wall switch in the desired position on a wall. Run a maximum of 25 feet (7.8 m) or less length of 18 A.W.G. minimum wire and connect it to the fireplace ON/ OFF switch pigtails.

WARNING: DO NOT CONNECT 110-120 VAC ! TO THE WALL SWITCH OR THE CONTROL

VALVE WILL BE DESTROYED.

Optional Accessories

Optional remote control kits require that 110-120 VAC be wired to the factory installed junction box before the fire- place is permanently installed.

CAUTION: LABEL ALL WIRES PRIOR TO DISCONNEC- TION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERA- TION. VERIFY PROPER OPERATION AFTER SERVICING.

Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. R • 2/05

31

Page 30 Page 32
Page 31
Image 31
Hearth and Home Technologies BE-36-CIPI manual Wiring the Fireplace, Valve will be Destroyed
Page 30 Page 32

BE-36-C, BE-36-CIPI specifications

Hearth and Home Technologies, a leader in innovative heating solutions, offers two remarkable gas fireplaces: the BE-36-CIPI and BE-36-C. Both models are designed to deliver efficient heating, aesthetic charm, and user-friendly features, making them ideal for modern living spaces.

The BE-36-CIPI is a direct vent fireplace that provides the warmth of a traditional fire without the hassle of wood. One of its most notable features is its contemporary design, featuring clean lines and a wide viewing area. This model comes with an impressive heat output, ensuring that spaces remain comfortably warm during chilly seasons. The BE-36-CIPI incorporates innovative technologies like the IntelliFire™ ignition system, which promotes energy efficiency by providing reliable performance while minimizing fuel consumption.

Moreover, the fireplace's advanced burner system creates a stunning flame pattern and realistic look, enhancing the ambiance of any room. With customizable options, homeowners can choose different media types, such as ceramic logs or contemporary stones, allowing for personal expression in their décor.

On the other hand, the BE-36-C model offers similar features but with its unique twist. This model is characterized by its traditional aesthetic appeal, making it an excellent choice for those who prefer a classic look with modern convenience. The BE-36-C also utilizes the IntelliFire™ system, ensuring efficiency and ease of use. With a versatile design, this fireplace can fit into various style preferences, from rustic to modern.

Both models come equipped with optional heat management systems, allowing for effective temperature regulation. This feature is particularly useful for maintaining a comfortable environment without overheating the space. The fireplaces are also designed with safety in mind, adhering to strict safety standards and offering numerous safety features like a safety pilot and tempered glass doors.

In conclusion, Hearth and Home Technologies’ BE-36-CIPI and BE-36-C gas fireplaces present an ideal blend of aesthetics, efficiency, and advanced technology. Whether opting for the contemporary style of the BE-36-CIPI or the classic allure of the BE-36-C, homeowners are guaranteed to enjoy a superior heating experience that complements their home’s design while providing warmth and comfort.
Top Page Image Contents