Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies CD4842R, CD4842ILR, CD4842LR, CD4236R, CD4236LR, CD4236ILR Dvp-Hrc-Ss

Models: CD4842R CD4842LR CD4236ILR CD4236LR CD4842IR CD4842ILR CD4236R CD4236IR

1 80

Download 80 pages 41.85 Kb

Page 66

B. Vent Components Diagrams (continued)

Fillers

DVP-TRAP to DVP-HPC Side Filler Kit

8-1/8 in.

(206 mm)

15in.

(381 mm)

13in.

(330 mm)

DVP-HRC-SS

Effective Length 5-3/4 to 8-3/8 in. 146 to 213 mm

	5-1/2 in.		8-3/8 in.
	140 mm		213 mm

	87°	3°

10-1/2 in.

267 mm

10-7/8 in.

276 mm

DVP-HRC-ZC-SS

Figure 16.6 DVP Vent Components

66	Heatilator • Caliber CD Series • 4040-263 Rev N • 11/08

Image 66

Hearth and Home Technologies CD4842R, CD4842ILR, CD4842LR, CD4236R, CD4236LR, CD4236ILR, CD4236IR, CD4842IR Dvp-Hrc-Ss

Contents

Direct Vent Gas Appliance Installation and OperationModels CD4236R CD4842R CD4236LR CD4842LR CD4236IR CD4842IR What to do if you smell gas Congratulations Homeowner Reference Information Table of Contents Installer GuideUser Guide Finishing Appliance SetupTroubleshooting Reference Materials Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of Liability Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Gas Fireplace Safety Operating InstructionsYour Fireplace Fan Kit optional Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear Space For Your Safety Read Before Lighting Lighting Instructions IPI Lighting StandingPilot Frequently Asked Questions After Fireplace is Lit Remote Control Maintenance and ServiceMaintenance Tasks-Homeowner Doors, Surrounds, Fronts Maintenance Tasks-Qualiﬁed Service Technician Getting Started Typical Appliance System Inspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Any such action may cause a ﬁre hazard Framing and Clearances Select Appliance LocationModel # Construct the Appliance Chase ClearancesRough Opening Model Width Height Depth Mantel and Wall Projections MantelsMantel Legs or Wall Projections Termination Locations Vent Termination Minimum Clearances Minimum Clearances for Termination Vent Table Key Vent Information and DiagramsApproved Pipe Use of Elbows Vent Diagrams Top Vent Horizontal TerminationOne Elbow Two 45 Elbows replacing One 90 Elbow Two ElbowsMin Max +H 2 max +H 2+H 3 max Installed Vertically Three Elbows Top Vent Vertical Termination No Elbow 12 ft 3.66 m min 60 ft 18.29 m max Rear Vent Horizontal Termination One 45 Elbow Two Elbows Rear Vent Vertical Termination Min Ft 1.83 m max 12 ft 3.66 m min 60 ft 18.29 m max Install Vertical Termination Bafﬂe 17 Flat Bafﬂe Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Install the Ceiling Firestop Installing Ceiling Firestop Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Appliance Preparation Convert from Top Vent to Rear Vent Outer Collar, Remove Four Screws 11 Place Outer Collar on Rear of Appliance 16 Cover Plate-Replace Secure and Level the Appliance 20 Proper Positioning, Leveling And Securing Of An Assemble Pipe Sections DVP Only Install Vent PipeAttach Pipe to the Firebox Assembly Assemble Pipe Sections Assemble Vent Sections SLP Only Assemble Slip Sections Secure the Vent Sections Disassemble Vent Sections Install Decorative Ceiling Components SLP only Install Metal Roof Flashing Assemble and Install Storm CollarCaulk Install RF4-8 SLP-FS Install Vertical Termination Cap Install Decorative Wall Components SLP onlyHeat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap Interior Gas Pressure Gas InformationFuel Conversion Gas Connection Intelliﬁre Ignition System Wiring Wiring RequirementsStanding Pilot Ignition System Wiring Optional Accessories Requirements Electrical Service and Repair WSK-MLT-HTL Junction Box Installation Wall Switch Installation for Fan Optional Finishing Facing MaterialCombustible Appliance Setup Air Shutter Setting Install Trim and/or SurroundInstall Hood Removing Fixed Glass Assembly Troubleshooting Symptom Possible Causes Corrective ActionStanding Pilot Ignition System Symptom Possible Cause Corrective Action Intelliﬁre Ignition System Will not ignite. If the pilot Appliance Dimension Diagram Reference Materials Vent Components Diagrams DVP Vent Components BEK DVP-BEK2 DVP-TVHW DVP-TRAP Horizontal Termination Cap DVP-HRC-SS Effective SL-2DVP Adapter Service Parts CD4236IR, CD4236ILR Service CD4236R, CD4236LR IPI Valve Assembly CD4842IR, CD4842ILR CD4842R, CD4842LR IPI Valve Assembly Optional Components Model # Description FFCM36BN This page intentionally left blank This page intentionally left blank This page intentionally left blank Contact Information