Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies CD4842R, CD4842ILR, CD4842LR Installed Vertically, Three Elbows

Models: CD4842R CD4842LR CD4236ILR CD4236LR CD4842IR CD4842ILR CD4236R CD4236IR

1 80

Download 80 pages 41.85 Kb

Page 26

Image 26

1. Top Vent - Horizontal Termination - (continued)

Three Elbows

	V1 min.		V1 + V2 max.		H1+H2 max.
	ft	m	ft	m	ft	m
DVP	1	0.30	24	7.32	19	5.79
SLP	1	0.30	22	6.71	19	5.79

Installed

Vertically

H2

V2

V1

H1

Figure 7.6

26	Heatilator • Caliber CD Series • 4040-263 Rev N • 11/08

Image 26

Hearth and Home Technologies CD4842R, CD4842ILR, CD4842LR, CD4236R, CD4236LR, CD4236ILR Installed Vertically, Three Elbows

Contents

Direct Vent Gas Appliance Installation and OperationModels CD4236R CD4842R CD4236LR CD4842LR CD4236IR CD4842IR What to do if you smell gas Congratulations Homeowner Reference Information User Guide Table of ContentsInstaller Guide Finishing Appliance SetupTroubleshooting Reference Materials Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of Liability Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Your Fireplace Gas Fireplace SafetyOperating Instructions Fan Kit optional Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear Space For Your Safety Read Before Lighting Lighting Instructions IPI Pilot LightingStanding Frequently Asked Questions After Fireplace is Lit Remote Control Maintenance and ServiceMaintenance Tasks-Homeowner Doors, Surrounds, Fronts Maintenance Tasks-Qualiﬁed Service Technician Getting Started Typical Appliance System Inspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Any such action may cause a ﬁre hazard Model # Framing and ClearancesSelect Appliance Location Rough Opening Model Width Height Depth Construct the Appliance ChaseClearances Mantel Legs or Wall Projections Mantel and Wall ProjectionsMantels Termination Locations Vent Termination Minimum Clearances Minimum Clearances for Termination Vent Table Key Vent Information and DiagramsApproved Pipe Use of Elbows One Elbow Vent DiagramsTop Vent Horizontal Termination Min Max +H 2 max +H 2+H 3 max Two 45 Elbows replacing One 90 ElbowTwo Elbows Installed Vertically Three Elbows Top Vent Vertical Termination No Elbow 12 ft 3.66 m min 60 ft 18.29 m max Rear Vent Horizontal Termination One 45 Elbow Two Elbows Rear Vent Vertical Termination Min Ft 1.83 m max 12 ft 3.66 m min 60 ft 18.29 m max Install Vertical Termination Bafﬂe 17 Flat Bafﬂe Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Install the Ceiling Firestop Installing Ceiling Firestop Vaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Appliance Preparation Convert from Top Vent to Rear Vent Outer Collar, Remove Four Screws 11 Place Outer Collar on Rear of Appliance 16 Cover Plate-Replace Secure and Level the Appliance 20 Proper Positioning, Leveling And Securing Of An Assemble Pipe Sections DVP Only Install Vent PipeAttach Pipe to the Firebox Assembly Assemble Pipe Sections Assemble Vent Sections SLP Only Assemble Slip Sections Secure the Vent Sections Disassemble Vent Sections Install Decorative Ceiling Components SLP only Caulk Install Metal Roof FlashingAssemble and Install Storm Collar Install RF4-8 SLP-FS Heat Shield Requirements for Horizontal Termination Install Vertical Termination CapInstall Decorative Wall Components SLP only Install Horizontal Termination Cap Interior Gas Pressure Gas InformationFuel Conversion Gas Connection Intelliﬁre Ignition System Wiring Wiring RequirementsStanding Pilot Ignition System Wiring Optional Accessories Requirements Electrical Service and Repair WSK-MLT-HTL Junction Box Installation Wall Switch Installation for Fan Optional Combustible FinishingFacing Material Appliance Setup Air Shutter Setting Install Trim and/or SurroundInstall Hood Removing Fixed Glass Assembly Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Symptom Possible Cause Corrective Action Intelliﬁre Ignition System Will not ignite. If the pilot Appliance Dimension Diagram Reference Materials Vent Components Diagrams DVP Vent Components BEK DVP-BEK2 DVP-TVHW DVP-TRAP Horizontal Termination Cap DVP-HRC-SS Effective SL-2DVP Adapter Service Parts CD4236IR, CD4236ILR Service CD4236R, CD4236LR IPI Valve Assembly CD4842IR, CD4842ILR CD4842R, CD4842LR IPI Valve Assembly Optional Components Model # Description FFCM36BN This page intentionally left blank This page intentionally left blank This page intentionally left blank Contact Information