Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies CUMBGAP-MBK Reversible Flue Collar, Cumberland Gap Wood Stove

Models: CUMBGAP-PMH CUMBGAP-MBK

1 36

Download 36 pages 63.38 Kb

Page 10

REVERSIBLE FLUE COLLAR

R

Cumberland Gap Wood Stove

REVERSIBLE FLUE COLLAR

The ﬂue collar is reversible for either a top or rear venting installation. The unit is shipped with the ﬂue collar in the top vent position.

ACCESSORY HORIZONTAL FLUE SHIELD

Part HTSHLD-7006

IS REQUIRED ON ALL HORIZONTAL INSTALLATIONS.

CONVERTING COLLAR FOR REAR VENT INSTALLATION
1. Lift off cast top. Remove 4 Phillips head screws from the
	heat shield and discard heat shield. See circled areas in
	Figure 10A.
2.	Remove 4 Phillips head screws from the rear shield, 2
	on each side, lift rear heat shield off and set aside.
3.	Remove 1 bolt from each side of the ﬂue collar using a
	Phillps head screwdriver and 7/16 wrench.
4.	Turn ﬂue collar to horizontal position. Inspect sealant to
	ensure a leak free application. Re-attach bolts.
5.	Re-attach the rear heat shield.
6.	Attach required accessory Horizontal Flue Shield with	Figure 10B
	screws provided. Figure 10B

7.Place cast top on the unit. See Figure 10C for completed view.

Secure

Horizontal Flue

Heat Shield

Remove cast top

Completed View

Figure 10A

Remove bolts and

rotate flue collar

Discard heat shield

Rear Heat

Shield

Remove 4 screws and set rear shield & screws aside

Figure10C

Page 10

7006-188E

September 1, 2008

Image 10

Hearth and Home Technologies CUMBGAP-MBK, CUMBGAP-PMH Reversible Flue Collar, Cumberland Gap Wood Stove, Remove cast top

Contents

Non-Catalytic, Front/Side Load, Wood Heater IMPORTANT SAFETY NOTESCumberland Gap CUMBGAP-MBK CUMBGAP-PMHSerial Number Testing LabCumberland Gap Wood Stove Model NameINSTALLATIONS MATERIAL NEEDED FOR SAFETY TABLE OF CONTENTSPRE-USE CHECK LIST DIMENSIONS & VENT SPECIFICATIONSCHIMNEY SYSTEMS Cumberland Gap Wood Stove LISTINGS and SAFETY NOTICESINSTALLATION MATERIALS NEEDED FOR YOUR SAFETY VENTING SYSTEMSERIAL NUMBER LABEL IS LOCATED ON THE BACK OF THE STOVE Cumberland Gap Wood Stove DIMENSIONSVENT SPECIFICATIONS FRONT VIEWCLEARANCES TO COMBUSTIBLES UL and ULC Cumberland Gap Wood StoveNOTE Drawings are for illustration purposes only and are not to scale BOTH FUEL DOORS ACCESSIBLECumberland Gap Wood Stove FLOOR PROTECTION SIDE FUEL DOOR LOCKED SHUTCumberland Gap Wood Stove Calculating Alternate Floor Protection MaterialHORIZONTAL VENTING NOTE Drawings are for illustration purposes only and are not to scaleLEG LEVELING SYSTEM Cumberland Gap Wood Stove LOCATING YOUR STOVESIDE FUEL-LOADING-DOOR LOCKING MECHANISM UNLOCK SIDE FUEL DOORIS REQUIRED ON ALL HORIZONTAL INSTALLATIONS REVERSIBLE FLUE COLLARACCESSORY HORIZONTAL FLUE SHIELD Part HTSHLD-7006 CONVERTING COLLAR FOR REAR VENT INSTALLATIONFigure 11B - Chimney Connector FLUE SYSTEMSCHIMNEY HEIGHT REQUIREMENTS / DRAFT Cumberland Gap Wood StoveWood Stud 2 51mm Clearance from chimney wall Header MASONRY CHIMNEYCumberland Gap Wood Stove Fireclay liner 5/8 16mm Minimum or Equivalent Sill supportFigure 13A SOLID PACK CHIMNEY WITH METAL SUPPORTS AS A THIMBLECumberland Gap Wood Stove Figure 13BRequired Flue Shield not shown in diagram. See page CONNECTION TO A MASONRY FIREPLACESOLID PACK CHIMNEY WITH METAL SUPPORTS AS A THIMBLE Contd Cumberland Gap Wood StoveINTERIOR CHIMNEY CONNECTION TO A METAL PREFABRICATED CHIMNEYFigure 15A Figure 15BWARNING! DO NOT INSTALL IN SLEEPING ROOM Cumberland Gap Wood Stove MOBILE HOME INSTALLATIONDO NOT CUT THROUGH FLOOR JOIST, WALL STUD, CEILING TRUSS, ETC The blower is shipped fully assembled and ready for installation OUTSIDE AIR KIT INSTALLATION PartINSTALLATION OF OPTIONAL BLOWER, Part If NecessaryBafﬂe Diverter is shipped inside ﬁrebox BENDING TEMPLATE STRAIGHT ENDCUT ENDS Cumberland Gap Wood StoveStraight end to the back Cut end to the front BAFFLE DIVERTER REQUIRED ON ALL HORIZONTAL INSTALLATIONSSlanted corner Ceramic Blanket Manifold chamberCumberland Gap Wood Stove OPERATING INSTRUCTIONS IMPORTANT - PLEASE READ BEFORE USING STOVE1. Symptoms of Over-Firing Fire RiskSTART-UP AIR SYSTEM AIR CONTROLSCumberland Gap Wood Stove Figure 21ACumberland Gap Wood Stove HEAT OUTPUT SETTINGSBUILDING A FIRE BTU / HrCORRECT POSITION CORRECT BAFFLE & BLANKET PLACEMENTINCORRECT POSITIONS Cumberland Gap Wood StoveWOOD SELECTION AND STORAGE OPERATING INSTRUCTIONS Cont’d OPACITYBURN RATES OPTIONAL BLOWER OPERATING INSTRUCTIONSCREOSOTE MAINTENANCECHIMNEY CLEANING ASH REMOVALCARE AND CLEANING OF PLATED SURFACES Cumberland Gap Wood Stove MAINTENANCE ContdGLASS REPLACEMENT DOOR GASKETCumberland Gap Wood Stove MAINTENANCE CondBAFFLE REMOVAL & INSTALLATION Brick Set Part Number BRICK-700623.0 Parts DiagramCumberland Gap Wood Stove 14-1/4Cumberland Gap Wood Stove Service Parts & AccessoriesDescription Firescreen - Can only be used in Full Verticial Installations Service Parts & AccessoriesAccessories Horizontal Flue Shield - Required for all Horizontal InstallationsDescription of Service Service & Maintenance LogDate of Service Cumberland Gap Wood StoveCumberland Gap Wood Stove Warranty PolicyHearth & Home Technologies LIMITED WARRANTY CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITYHearth & Home Technologies LIMITED WARRANTY Contd Cumberland Gap Wood Stove7006-188E Cumberland Gap Wood Stove This page intentionally left blankPage September 17006-188E Cumberland Gap Wood Stove This page intentionally left blankSeptember 1 PageCONTACT INFORMATION Cumberland Gap Wood StoveYour Records for Model Hearth & Home Technologies 1445 North Highway Colville, WA