Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies Cyclone-Cust C. Service Parts, Stocked, at Depot, Description

Models: Cyclone-Cust

1 46

Page 42

	C. Service Parts	CYCLONE-CUST

	Service Parts Diagram	Beginning Manufacturing Date: May 2004
	Service Parts Diagram	Ending Manufacturing Date: ______
		Ending Manufacturing Date: ______

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement				Stocked
parts for your appliance please provide model number and serial number. All parts listed				Stocked
in this manual may be ordered from an authorized dealer.				at Depot
ITEM	DESCRIPTION	COMMENTS	PART NUMBER
1	Top Cover Assembly		2061-005
2	Tube Assembly		2061-015
3	Ignitor	Pre Aug 2007	SRV2061-165	Y
3	Ignitor	Post Aug 2007	2061-165	Y
		Post Aug 2007	2061-165	Y
4	Flame Sensor		2061-142	Y
	Fan Blade		2061-108
	Flue Restrictor	2.5” Hole	2061-203
	Flue Restrictor	2.75” Hole	2061-204

Additional service part numbers appear on following page.

42	Heat & Glo • Cyclone-Cust • 2061-900 Rev. L • 10/08

Page 42

Image 42

Hearth and Home Technologies Cyclone-Cust C. Service Parts, Stocked, at Depot, Description, Comments, Part Number

Contents

Model Cyclone-Cust What to do if you smell gasOwner’s Manual Homeowner Reference Information Congratulations8 Installing Vent Pipe Table of Contents5 Vent Information and Diagrams 12 Appliance SetupA. Appliance Certiﬁcation D. High Altitude Installations1 Listing and Code Approvals B. Glass SpeciﬁcationsApproved Carbon Monoxide Detectors H. Requirements for the Commonwealth of MassachusettsInstallation of Carbon Monoxide Detectors SignageC. Inspect Appliance and Components A. Design and Installation Considerations2 Getting Started B. Tools and Supplies NeededNote For actual appliance dimensions refer to Sec- tion 3 Framing and ClearancesA. Selecting Appliance Location ModelC ED F MAX B. Constructing the Appliance ChaseC. Clearances Figure 3.2 Clearances to CombustiblesFIRESTOP D. Mantel ProjectionsSLIP SECTION FRAMING MEMBER COMBUSTIBLE MATERIAL GLASSSee Figure 4.4 for speciﬁc clearances 4 Termination LocationsA. Vent Termination Minimum Clearances Roof Pitch= VENT TERMINAL = AREA WHERE TERMINAL IS NOT PERMITTEDAlcove Applications X = AIR SUPPLY INLETB. Use of Elbows 5 Vent Information and DiagramsA. Vent Table Key C. Measuring StandardsTwo Elbows D. Vent Diagrams1. Top Vent - Horizontal Termination One Elbow VT HTThree Elbows H2 H11. Top Vent - Horizontal Termination - continued VT MinTwo Elbows 2. Top Vent - Vertical TerminationNo Elbow VT V2VT Min 2. Top Vent - Vertical Termination - continuedThree Elbows HT MaxB. Wall Penetration Framing 6 Vent Clearances and FramingA. Pipe Clearances to Combustibles Combustible Wall PenetrationC. Vertical Penetration Framing Installing the Ceiling FirestopInstalling Attic Shield 7 Appliance Preparation A. Securing and Leveling the ApplianceDVP Series Venting Only 8 Installing Vent PipeA. Assembly of Vent Sections Assembling Pipe SectionsAssembling Minimum Installations MI Sections Assembling DVP-12A Slip SectionsB. Disassembly of Vent Sections Securing the Vent Sections Vertical SectionsHorizontal Sections C. Installing Heat Shield and Horizontal Termination Cap Installing the Horizontal Termination CapHeat Shield Requirements for Horizontal Termination D. Installing Roof Flashing and Vertical Ter- mination Cap Assembling and Installing Storm Collar B. Gas Pressures 9 Gas InformationA. Fuel Conversions C. Gas ConnectionHIGH ALTITUDE INSTALLATIONS A. Recommendation for Wire 10 Electrical InformationPlastic grommet B. Connecting to the Appliance C. Hot Surface Ignition WiringOptional Accessories Requirements 11 Finishing A. Mantel ProjectionsB. Facing Material C. Accessories 12 Appliance SetupB. Clean the Appliance D. Glass Assembly InstallationHigh temperatures may ignite clothing or other ﬂammable materials 13 Operating InstructionsA. Before Lighting Appliance Before operating this appliance have a qualiﬁed tech- nicianFOR YOUR SAFETY READ BEFORE LIGHTING B. Lighting Appliance HSI IgnitionFinal inspection by Turn off all electric power to the applianceD. Frequently Asked Questions C. After Appliance is LitInitial Break-in Procedure A. Fan Motor Service 14 Maintaining and Servicing ApplianceSCREWS Figure 14.2 The glass platform plate can now be removed by removing the 13 screws on the outer edge of this plat- form. Lift the platform. The HSI Hot Surface Ignitor and the sensor wire can be unplugged. Set platform aside B. Maintenance Tasks Maintenance TasksInspect ACCESS A. Appliance Dimension Diagram15 Reference Materials ACCESSB. Vent Components Diagrams Heat & Glo Cyclone-Cust 2061-900 Rev. L 10/08B. Vent Components Diagrams continued Figure 15.3 DVP vent componentsExtended Heat Shield B. Vent Components Diagrams continuedDVP-HSM-B 31 inStocked C. Service PartsCYCLONE-CUST at DepotCYCLONE-CUST Valve AssemblyService Parts StockedD. Limited Lifetime Warranty Hearth & Home Technologies LIMITED WARRANTYCONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY D. Limited Lifetime Warranty continued Please contact your Heat & Glo dealer with any questions or concerns E. Contact InformationDO NOT DISCARD THIS MANUAL For the location of your nearest Heat & Glo dealer

C. Service Parts

CYCLONE-CUST

Stocked

at Depot

DESCRIPTION

COMMENTS

PART NUMBER