Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies GBST4336I Top View, 1/2 in. Min, Fireplace Opening, 2-3/4 in. Min

Models: GBST4336I GBFL4136I

1 50

Download 50 pages 62.47 Kb

Page 21

Image 21

Combustible Mantel Legs or Wall Projections

TOP VIEW

1/2 in. Min.

FIREPLACE

OPENING

Note: Clearance from opening to perpendicular wall.

2-3/4 in. Min.

1 in.		Unlimited



Max.

3-1/4 in. Min.

Figure 5.8 Clearances to Combustible Mantel Legs or Wall Projections (Acceptable on both sides of opening.)

SHEETROCK

3-1/4 in.

AIR SPACE REQUIRED

Figure 5.9 Non-Combustible Zone

Heatilator • GBST4336I, GBFL4136I • 2135-900 Rev. D • 11/08

Page 21

Image 21

Hearth and Home Technologies GBST4336I Top View, 1/2 in. Min, Fireplace Opening, 2-3/4 in. Min, 1 in, 3-1/4 in. Min

Contents

What to do if you smell gas Model GBST4336I GBFL4136IHomeowner Reference Information A. CongratulationsRead this manual before installing or operating this appliance Please retain this owner’s manual for future referenceSafety Alert Key Table of ContentsInstaller Guide User GuideC. Clean the Appliance D. Accessories A. Remove Glass Assembly B. Remove the Shipping MaterialsE. Lava Rock and Glowing Ember Placement F. Install the Log Assembly G. Fixed Glass Assembly H. Install Trim Kits and SurroundsB. Limited Lifetime Warranty Hearth & Home Technologies LIMITED WARRANTYCONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY B. Limited Lifetime Warranty continued 1 Listing and Code Approvals D. High Altitude InstallationsA. Appliance Certiﬁcation B. Tempered Glass SpeciﬁcationsA. Gas Fireplace Safety 2 Operating Instructions User GuideB. Your Fireplace F. Remote Controls, Wall Controls and Wall Switches E. Fixed Glass AssemblyC. Clear Space D. Decorative Doors and FrontsWARNING CAUTION FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS IPI TO TURN OFF GAS TO APPLIANCEJ. After Fireplace is Lit K. Frequently Asked QuestionsISSUE SOLUTIONSA. Maintenance Tasks-Homeowner 3 Maintenance and ServiceGlass Cleaning Remote ControlGasket Seal and Glass Assembly Inspection B. Maintenance Tasks-Qualiﬁed Service TechnicianLogs FireboxA. Typical Appliance System Getting StartedInstaller Guide Figure 4.1 Typical SystemC. Tools and Supplies Needed B. Design and Installation ConsiderationsD. Inspect Appliance and Components WARNING! Risk of Fire, Explosion or Electric ShockE. Negative Pressure A. Selecting Appliance Location 5 Framing and ClearancesGBFL4136I MINIMUMB. Constructing the Appliance Chase C. ClearancesMINIMUM FRAMING DIMENSIONS 31-5/8 38-1/81016 GBFL4136IGBST4336I Mantel Projection D. Mantel and Wall ProjectionsGBFL4136I Mantel Projection GBST4336I Mantel Projection1/2 in. Min TOP VIEWFIREPLACE OPENING 2-3/4 in. MinA. Vent Termination Minimum Clearances 6 Termination LocationsFire Risk Maintain vent clearance to combustibles as speciﬁed DO NOT pack air space with insulation or other materialsA. Vent Guidelines 7 Vent Information and DiagramsB. Vent System Conﬁguration Install ﬁrestops as speciﬁedA. Pipe Clearances to Combustibles 8 Vent Clearances and FramingB. Wall and Ceiling Penetration Framing C. Vertical Penetration Framing9 Appliance Preparation A. Installing Outside Air Kit Damper Assem- blyB. Gas and Electrical Connections WARNING! Risk of Fire/Asphyxiation. DO NOT draw outWARNING! Risk of Fire! Prevent contact with C. Securing and Leveling the ApplianceSagging or loose insulation Insulation backing or plastic Framing and other combustible materialsA. Assembly of Vent Sections 10 Installing Vent PipeD. Install Attic Insulation Shield B. Attaching Vent to FireboxA. Fuel Conversion 11 Gas InformationB. Gas Pressure C. Gas ConnectionB. Intelliﬁre Ignition System Wiring A. Wiring RequirementsC. Optional Accessories Requirements 12 Electrical InformationD. Electrical Service and Repair MODULE 3 VACBLACK E. Junction Box Installation NOTICE DO NOT wire110 VAC to wall switch A. Splatter Guard 13 FinishingFigure 13.7 Prepare to Open Lower Access Panel To Close the Lower Access PanelFigure 13.8 Opening Lower Access Panel Figure 13.10 Splatter Guard with Lower Access Panel OpenGBFL4136I Pier Mantel Projection B. Mantel and Wall ProjectionsGBST4336I Mantel Projection GBFL4136I Mantel ProjectionC. Facing Material A. Remove Glass Assembly 14 Appliance SetupC. Clean the Appliance D. AccessoriesLog Set Assembly LOGS-2129 LOG PLACEMENTF. Install the Log Assembly 1 A C1 in Model GDCR4136IFigure 12. Placement of Log #2 Figure 11. Placement of Log #2Figure 13. Placement of Log #3 2 1 inH. Install Trim Kits and Surrounds G. Fixed Glass AssemblyI. Air Shutter Setting Removing Fixed Glass AssemblyA. Intelliﬁre Ignition System 15 Troubleshootinga. Incorrect wiring Verify “S” wire white for sensor and “I” wire orange for ignitorVerify all connections to wiring diagram in manual. Verify Intelliﬁre Ignition System - continuedconnections underneath pilot assembly are tight. Verify With ﬁxed glass assembly in place, verify that ﬂame is en16 Reference Materials A. Appliance Dimension DiagramLocation InchesØ J L A B FRONT VIEW MN OK C D F E G LocationB. Service Parts Log Set AssemblyC 3 B GBST4336Iat Depot GBST4336IB. Service Parts StockedLog Set Assembly GBFL4136IB. Service Parts Service Parts DiagramGBFL4136I B. Service Parts ListStocked at DepotService Parts IPI Valve AssemblyGBST4336I, GBFL4136I Stockedand maintenance C. Contact Informationinstallation and operation DO NOT DISCARD THIS MANUAL

TOP VIEW

1/2 in. Min.

FIREPLACE

Note: Clearance from opening to perpendicular wall.

2-3/4 in. Min.

1 in.

Unlimited

3-1/4 in. Min.

SHEETROCK