R
Yosemite Wood Stove
OUTSIDE AIR KIT INSTALLATION
Part
Included in Kit: 2 cable ties; oustide air termination cap; mounting screws (Discard the remaining parts).
In Stove's Component Pack: Outside air cover plate
Items Needed for Installation: 4 inch (102mm) diameter flex pipe in the length as required for your installation; Phillips screwdriver; Silicone sealant; Drills and saws necessary for cutting holes through the wall or flooring in your home.
Remove all materials from packing box and stove component pack
.
1.Remove ash lip by using a 7/16” wrench and remove the 2 bolts underneath the ash lip. Carefully lower and set aside.
2.Swing open ash removal door.
OUTSIDE AIR |
TERMINATION CAP |
(contains rodent screen) |
OUTSIDE AIR |
INTAKE |
3. Remove 2 screws from the stove bottom. Place cover over the air | Figure 17A |
opening and secure with same 2 screws. Figure 17B. |
|
4. Mount the flex flange (with pipe fitting extending out), over the intake air opening at the rear of the stove using the four mounting screws supplied with the kit. Figure 17A.
Cut a 4 inch (102mm) minimum hole in the floor or wall to accommo- date outside air piping. Use 4 inch (102mm) metal flex or rigid piping to directly connect outside air to the unit or into vented crawl space.
(Do not put flex into a
If using flex tubing attach cable ties to secure tubing at both ends. Use |
| |
the supplied termination cap with a rodent screen. Seal between the floor | OUTSIDE AIR | |
or wall and the pipe with silicone to prevent moisture penetration. | ||
COVER PLATE | ||
| ||
NOTE: If you plan to install the optional blower AND the | Figure 17B | |
| ||
outside air kit, complete the installation of the |
|
| outside air kit FIRST. | ADJUSTING THE BLOWER SPEED CONTROL | ||
| INSTALLATION OF OPTIONAL BLOWER |
| *If Necessary | |
| Part | *The blower speed control for this unit is adjusted at the factory, | ||
| The blower is shipped fully assembled | and normally does not require further adjustment. | ||
|
|
| ||
| and ready for installation. |
| NOTE: When the speed control is turned | |
1. | Remove 3 phillips head screws from rear of stove. |
| clockwise, it will click on to high speed. Turn | |
| the speed control clockwise to decrease the | |||
2. | Using the phillips head screws, attach blower to lower rear of stove, as | |||
speed. At full clockwise, the blower should | ||||
| shown. |
| ||
|
| blow gently, but should not stop. | ||
3. | Plug blower cord into a grounded outlet. Do not remove ground prong from | |||
| ||||
| plug. Route power cord to avoid heat from the stove, or other damage. | 1. With the stove plugged in, turn the speed | ||
| Do not route cord under or in front of appliance. |
| ||
|
| control knob to slow (full clockwise). | ||
4. | Adjust the blower speed control to the desired speed. |
| ||
|
|
|
|
| 2. | With a small screwdriver, adjust the blower |
|
|
|
| speed by turning the adjustment mechanism |
BLOWER |
|
|
| through the hole on the side of the speed |
MOUNTING |
|
| control. | |
FLANGE |
|
|
| |
| REAR SHIELD |
|
| |
|
| 3. | Adjust the speed so the blower runs slowly, | |
|
|
| ||
| REAR | BLOWER MOUNTING |
| but does not stop. Turn clockwise to slow the |
| SHIELD | FLANGE |
| blower and counterclockwise to increase the |
|
|
| ||
|
|
|
| speed. |
|
| BLOWER SPEED CONTROL |
|
|
|
|
| Figure 17C |
|
September 1, 2008 |
|
| Page 17 |