Installing the Trim

Combustible materials may be brought up to the specified clearances on the side and top front edges of the fireplace, but MUST NEVER overlap onto the front face. The joints between the finished wall and the fireplace top and sides can only be sealed with a 300° F. (149° C) minimum sealant.

WARNING: WHEN FINISHING THE FIRE-

!PLACE, NEVER OBSTRUCT OR MODIFY THE AIR INLET/OUTLET GRILLES IN ANY MANNER.

Install optional marble and brass trim surround kits as desired. Marble, brass, brick, tile, or other non- combustible materials can be used to cover up the gap between the sheet rock and the fireplace.

Do not obstruct or modify the air inlet/outlet grilles. When overlapping on both sides, leave enough space so that the bottom grille can be opened and the trim door removed.

1.7INSTALLER TESTING

The space heater must be tested and be operating ac- cording to manufacturer's specifications prior to the in- staller leaving the site. Note: the tips of the flames should never hit the top of the firebox after the unit has warmed up. Please contact your dealer or a qualified service person to replace injector or adjust valve.

Upon completing the gas line connection, a small amount of air will be in the lines. When first lighting the pilot light, it will take a few minutes for the lines to purge themselves of this air. Once the purging is com- plete, the pilot and burner will light and operate as indi- cated in the Lighting Instructions.

Subsequent lightings of the appliance will not require such purging.

Follow the Safety Information and Lighting Instructions pages of this manual to light the appliance.

To obtain proper operation, it is imperative that the pi- lot and main burner flame characteristics are steady, not lifting or floating. Typically, the top 3/8-inch (10mm) of the thermocouple should be engulfed in the pilot flame (see Figure 35).

Burner flame patterns are shown in Figure 36.

Proper gas log positioning is shown in Section 1.8.

Follow Section 3.5 TROUBLESHOOTING for adjusting the appliance to operate properly.

Pilot Assembly

Figure 35.

MAKE SURE THE FLAMES

ARE STEADY—NOT

LIFTING OR FLOATING.

Figure 36.

Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06

26

Page 25 Page 27
Page 26
Image 26
Hearth and Home Technologies SL-350TRSI-AUE manual Installer Testing, Installing the Trim, Pilot Assembly
Page 25 Page 27

SL-350TRSI-AUE specifications

The Hearth and Home Technologies SL-350TRSI-AUE is a remarkable addition to the realm of contemporary fireplace solutions, designed to enhance both aesthetics and functionality in homes. This model exemplifies the company’s commitment to creating high-quality heating appliances that not only provide warmth but also serve as a stunning centerpiece for any living space.

One of the key features of the SL-350TRSI-AUE is its state-of-the-art linear design. This fireplace is constructed to provide a clean, modern aesthetic that seamlessly integrates into a variety of interior styles. With a sleek frame and expansive glass viewing area, it offers a panoramic view of the flames, allowing for an immersive experience. The linear orientation also creates a more open feel in a room, making it a favored choice for contemporary living spaces.

In terms of technology, the SL-350TRSI-AUE is equipped with advanced direct vent capabilities, ensuring efficient combustion and enhanced safety. The direct vent system pulls air from outside for combustion and exhausts directly outside, maintaining indoor air quality and optimizing heating efficiency. This is particularly beneficial in energy-smart homes, where maintaining indoor air quality is paramount.

The fireplace also features a powerful, adjustable flame control, enabling users to customize their heating experience according to personal preferences. With its thermostat compatibility, homeowners can set their desired temperature, and the fireplace will automatically adjust to provide consistent warmth. This smart heating solution ensures comfort throughout the colder months while also keeping energy consumption in check.

With regard to installation, the SL-350TRSI-AUE offers versatility. Its flexible venting options allow for installation in various locations, whether it be on an exterior wall or in a basement. The unit is designed to work under a variety of building conditions, providing engineers and contractors with greater flexibility during the design and installation processes.

Additionally, the fireplace features a minimalist remote control, allowing users to operate the unit effortlessly from anywhere in the room. The combination of these features makes the Hearth and Home Technologies SL-350TRSI-AUE a practical yet stylish choice for those seeking an efficient and visually appealing heating solution. With its blend of modern design, advanced technology, and functionality, it stands out as an exemplary product in the competitive fireplace market.
Top Page Image Contents