INSTALLATION

For easy installation, select an existing light with a wall switch for replacement.

For best performance, mount the fixture about 8 ft. (2.4 m) above the ground.

CAUTION: To Avoid Fire Or Burn Hazards:

¥Allow fixture to cool before touching. The bulb and the fixture operate at high temperatures.

¥Keep fixture at least 1" (2.5 cm) from combustible materials. Do not aim at objects closer than 3 ft. (1 m).

¥Use only T3, 250W (max.) tungsten halogen 120 VAC lamps.

❒Note the position of the various parts of the fixture for the type of installation for your application and adjust the lamp head and sensor as shown below.

Wall Mount

Eave Mount

Lens Retainer

Light Shield,

with opening at

this side

Lens Retainer

BULB INSTALLATION.

❒When relamping, turn power off and let the fixture cool.

❒Remove glass cover and remove the old bulb by pushing the bulb towards the socket indicated on the metal reflector.

❒To insert the new bulb, follow the instructions printed on the metal reflector.

❒Check that the bulb is seated properly.

❒Reinstall the glass cover.

WIRE THE LIGHT CONTROL.

❒Turn the power to the lighting circuit off at the fuse or circuit breaker box.

❒Remove the existing light fixture.

❒Install mounting strap to junction box using screws appropriate for your junction box.

❒The plastic hanger can be used to hold the fixture while wiring. The small end of the plastic hanger can be threaded through the hole in the center of the cover plate. The small end then goes into one of the slots on the mounting strap.

❒Thread all fixture wires through the large holes in the gasket as shown.

❒Connect the junction box wires to the light fixture wires as shown. Twist together and secure with wire connectors.

For under eave installation, the sensor head must be rotated as shown in the next two steps for proper opera- tion and to avoid the risk of electrical shock. Also for proper under eave operation, remove the protective backing from the Light Shield and stick on as shown below.

For eave mount only:

❒Swing the sensor head towards the clamp screw

joint.Controls Clamp Screw

Mounting Strap

Black to Black

White to White

Rubber

Plug

Mounting

Bolt

Gasket

❒Then rotate the sensor head clockwise 180° so the controls face down.

Controls

Light Shield

Opening

Controls

If the sensor pops out of the ball joint, loosen the clamp screw and push the sensor back into the ball joint. Tighten the clamp screw when done.

Connect any fixture ground wire(s) and the cover plate ground screw to the junction box ground wire.

MOUNT THE LIGHT CONTROL.

❒Align the Light Control cover plate and cover plate gasket. Secure with the mounting bolt.

❒Push the Rubber Plug firmly into place.

❒If a wet location junction box was not used, caulk the wall plate mounting surface with silicone weather sealant.

2

595-5295-11

Page 1 Page 3
Page 2
Image 2
Heath Zenith SL-5525 manual Wall Mount Eave Mount, Bulb Installation, Wire the Light Control, Mount the Light Control
Page 1 Page 3

SL-5525 specifications

The Heath Zenith SL-5525 is a versatile and innovative outdoor motion-activated security light designed to enhance safety and visibility around homes and businesses. It combines advanced technology with practical features to provide an effective solution for deterring intruders and illuminating dark areas.

One of the main features of the SL-5525 is its motion-detection capability. It is equipped with a passive infrared (PIR) sensor that can detect movement within a range of up to 30 feet. This allows the light to automatically turn on when it detects motion, providing immediate illumination where it is needed most. The sensor is adjustable, allowing users to customize the detection range and angle based on their specific needs. This ensures that the light activates only when necessary, contributing to energy efficiency.

In addition to its motion-activated function, the SL-5525 has a built-in dusk-to-dawn sensor. This feature enables the light to illuminate automatically at dusk and turn off at dawn, providing round-the-clock security without requiring manual operation. Users can rely on this light to enhance visibility during nighttime hours, ensuring that pathways are well-lit and reducing the risk of accidents or unwanted incidents.

The SL-5525 also boasts a durable construction designed to withstand various weather conditions. Its weather-resistant housing ensures that it remains functional even in harsh environments, making it an ideal choice for outdoor installation. The light is equipped with LED bulbs, which are known for their longevity and energy efficiency. These LED lights not only consume less energy than traditional bulbs but also have a longer lifespan, reducing the frequency of replacements and maintenance.

Another notable characteristic of the Heath Zenith SL-5525 is its sleek and modern design that seamlessly integrates into different outdoor aesthetics. It is available in several finishes to match various home styles, adding to its appeal as a decorative yet functional fixture.

Overall, the Heath Zenith SL-5525 is an excellent choice for homeowners and business owners looking for a reliable, efficient, and stylish outdoor lighting solution. Its combination of motion detection, dusk-to-dawn functionality, robust construction, and energy-saving LED technology makes it a standout option for enhancing security and visibility in any outdoor setting.
Top Page Image Contents