3

Press the OK button.

 

 

 

 

• The information concerning the program is

 

 

displayed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• When using the SHOWVIEW function for the first

 

time with stored stations, the program number

 

flashes. This one time, you must enter the PR

 

number manually by pressing the 34 buttons.

 

Refer to the following page if:

 

 

 

 

• The program number or times flash

 

• You wish to modify the program.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVD-RAM(VR)

 

Scheduled Record List

 

 

 

 

 

 

 

 

 

 

 

 

Remaining Recording Time 02:12 SP

 

 

 

No.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No. 01

 

 

 

 

 

Edit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

01

 

CH 09

11/22

09:22AM

10:30AM

Once

SP

 

 

 

 

 

 

 

 

 

 

 

Source

PR 01

 

 

Date

01/ 01

 

 

 

 

 

 

02

 

CH 05

12/10

 

12:30AM

09:00PM

Weekly LP

 

 

 

 

 

 

 

 

 

 

Start---

12

--: /-00-

--:--End--

--14:--:

--00

--

--

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Type

Once

 

 

Mode

SP

 

 

 

 

 

 

 

 

 

V/P

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MOVE

 

 

OK

 

 

RETURN

 

EXIT

 

 

 

 

 

 

 

 

 

DVD-RAM(VR)

 

Scheduled Record List

 

 

 

 

 

 

 

 

 

Remaining Recording Time 02:12 SP

 

 

 

No.

 

Source

Date

Start

End

 

Type

Mode

V/P Edit

 

 

 

01

PR 01

01/ 01 12:00

14:00

 

Once

SP

Off

 

 

 

02

-- --

--- -- --:--

--:-- --

 

--

--

 

 

 

 

 

 

MOVE

 

 

OK

 

 

RETURN

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4 If the program and times are correct, press the OK button.

5 Press the STANDBY/ON button to activate the timer.

6 Refer to pages 43~45 if you wish to:

• Check that your DVD Recorder has been programed correctly.

• Cancel a preset recording.

The numbers next to each TV program listing in

NOTE the magazines or newspapers are SHOWVIEW code numbers, which allow you to program your

DVD recorder instantly with the remote control.

Tap in the SHOWVIEW code for the program you wish to record.

SHOWVIEW is a trademark of Gemstar Development Corporation. The SHOWVIEW system is manufactured under license from Gemstar Development Corporation.

SHOWVIEW Extended

To prevent delays or over-runs, DVD-Recorder has a function called SHOWVIEW Extended allowing you to extend the recording time by up to 60 minutes.

1 Press the MENU button.

With the DVD in Stop press the MENU button.

2 Press the 34 button to select “Program” and then press the OK or 1 button.

 

DVD-RAM(VR)

 

Program

 

 

 

 

 

 

 

 

 

SHOWVIEW

 

 

 

 

 

Standard Timer

 

 

 

 

 

SHOWVIEW Extended

: Off

 

 

 

 

 

 

 

 

MOVE

OK

RETURN

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

3 Press the corresponding 34 buttons, until the “SHOWVIEW Extended” option is selected.

4 Press the OK or 1 buttons to set the “SHOWVIEW Extended” time by increments of 10 minutes.

5 To turn off, press OK or 1 buttons repeatedly until Off shows.

46 - English

Page 46
Image 46
Hitachi DV-RX7000E instruction manual Showview Extended, Press the Menu button, With the DVD in Stop press the Menu button