Definitions, Specifications | Hobart Welding Products 4500 instruction

SECTION 3 − DEFINITIONS

3-1. Symbol Definitions

	Engine Choke		Read Operator’s	A	Amperes	V	Volts
	Engine Choke		Manual		Amperes		Volts
			Manual
	Engine Oil		Fuel		Battery (Engine)		Engine
	Positive		Negative		Alternating Current		Output
	Positive		Negative		(AC)		Output
h		s			(AC)
h	Hours	s	Seconds		Time		Protective Earth
							Protective Earth
							(Ground)
							(Ground)

Circuit Protector

Temperature

SECTION 4 − SPECIFICATIONS

4-1. Weld, Power, And Engine Specifications

Welding	Weld	Rated	Maximum	Generator	Fuel
Welding	Output	Rated	Open Circuit	Generator	Fuel	Engine
Mode	Output	Welding Output	Open Circuit	Power Rating	Capacity	Engine
Mode	Range	Welding Output	Voltage	Power Rating	Capacity
	Range		Voltage

		140 A, 20 V,
		30% Duty Cycle		Single-Phase,		Briggs & Stratton
		130 A, 25 V		4.5 kVA/kW (Surge)		Intek
		130 A, 25 V		4 kVA/kW		Air-Cooled,
		30% Duty Cycle		4 kVA/kW	1 gal (3.75L)	Air-Cooled,
CC/AC	60 − 140 A	30% Duty Cycle	80	(Continuous)	1 gal (3.75L)	One-Cylinder,
CC/AC	60 − 140 A	110 A, 25 V,	80	(Continuous)	Tank	One-Cylinder,
		110 A, 25 V,		20/17 A,	Tank	Four-Cycle,
		60% Duty Cycle		120/240 V AC,		Series 1450,
		90 A, 25 V,		60 Hz		Gasoline Engine
		100% Duty Cycle

OM-4418 Page 12

Page 16

Image 16

Hobart Welding Products 4500 manual Symbol Definitions, Weld, Power, And Engine Specifications

Contents

Processes OM-4418210 597KDescription From Hobart to You Table of Contents Page Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burns Fumes and Gases can be hazardous Buildup of GAS can injure or killARC Rays can burn eyes and skin Welding can cause fire or explosion Engine Hazards Compressed Air Hazards Welding Wire can cause injury HOT Parts can cause burns and injuryFire or Explosion hazard Falling Unit can cause injury Principal Safety Standards California Proposition 65 WarningsEMF Information Radiation can cause interference − Consignes DE Sécurité − Lire Avant Utilisation Signification des symbolesUN Choc Électrique peut tuer DES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peu- vent être dangereuxLE Soudage peut provoquer un incendie ou une explosion LE Bruit peut affecter l’ouïe ’EXPLOSION DE LA Batterie peut Rendre Aveugle DES Organes Mobiles peuvent provoquer des blessures ’AIR Comprimé peut provoquer des blessures LA Chaleur DU Moteur peut pro- voquer un incendieRisque D’INCENDIE OU D’EXPLO- Sion LE Surchauffement peut endom- mager le moteur électrique LES Fils DE Soudage peuvent provoquer des blessures’EMPLOI Excessif peut UNE Remorque QUI Bascule peut entraîner des blessures Proposition californienne 65 Avertissements Principales normes de sécuritéInformation EMF En ce qui concerne les implants médicaux − Specifications Symbol DefinitionsWeld, Power, And Engine Specifications − Definitions Dimensions, Weights, And Operating Angles Aux Power Gal./Hr Weld Power In KWFuel Consumption Weld Amps At Rated Duty Cycle Generator Power Curve AC Power VoltsAC Power Amperes Duty Cycle Volts Max Amp Min Amp Volt-Ampere CurvesAC Amps − Installation Installing Welding GeneratorRating Label Location Movement Grounding Generator When Supplying Building Systems Grounding Generator To Truck Or Trailer Frame 13 mm Full Gasoline Open/On Closed/Off Engine Prestart ChecksOil Connecting To Weld Output Terminals Connecting to weld Selecting Weld Cable Sizes150 ft 200 ft 250 ft 350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m Material Thickness Reference Chart − Operating the Welding Generator Controls See Section Description Of Controls See Section To Stop turn engine switch to OffAmperage Selection Table For Stick Smaw Electrodes Generator Power Panel Receptacles − Operating Auxiliary EquipmentUse GFCI-protected extension cord X 15 a + 240 V x 9 a = 4 kVA/KW OM-4418 − Maintenance Routine Maintenance Servicing Air Cleaner Stop engine − Troubleshooting TroubleshootingGenerator Power Welding Engine With proper viscosity oil for operating temperatureStarting difficult − Electrical Diagrams Circuit Diagram For Welding Generator − Generator Power Guidelines Selecting Equipment Grounding When Supplying Building Systems How Much Power Does Equipment Require?Use #10 AWG or larger insulated Resistive Load Volts 115 Amps Approximate Power Requirements For Industrial Motors Approximate Power Requirements For Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running Watts Power Required To Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 / Volts = Starting Amperage Typical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible Stick Welding Procedure − Stick Welding Smaw Guidelines Striking an Arc − Scratch Start Technique Electrode and Amperage Selection ChartStriking an Arc − Tapping Technique Poor Weld Bead Characteristics Good Weld Bead CharacteristicsPositioning Electrode Holder 10-30 9090 End View of Work Angle Conditions That Affect Weld Bead Shape Electrode Movement During Welding Butt Joints Lap JointTee Joint 16 in 30 1.6 mm Tack Welds Troubleshooting − Porosity Troubleshooting − Excessive SpatterWeld Test Possible Causes Corrective Actions Troubleshooting − Lack Of Penetration Troubleshooting − Incomplete FusionTroubleshooting − Excessive Penetration Troubleshooting − Waviness Of Bead Troubleshooting − Burn-ThroughTroubleshooting − Distortion Work like a Pro − Parts List Main Assembly SR1 Start Your Professional Welding Career Now Support ServiceAssistance Contact your Distributor for Hobart Welding Products

Hobart Welding Products 4500 manual Specifications, Symbol Definitions

Models: 4500

SECTION 3 − DEFINITIONS

3-1. Symbol Definitions

SECTION 4 − SPECIFICATIONS

4-1. Weld, Power, And Engine Specifications

Welding

Rated

Maximum

Generator

Fuel

CC/AC