INTRODUCTION IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
ELLIPTICAL
OPERATION
CONDITIONING TROUBLESHOOTING LIMITED
GUIDELINES & MAINTENANCE WARRANTY
30
M A I N T E N A N C E
WHAT KIND OF ROUTINE MAINTENANCE IS REQUIRED?
We use sealed bearings throughout our ellipticals so lubrication is not needed. The most important maintenance step is to simply wipe your perspiration off the trainer after each use.
HOW DO I CLEAN MY ELLIPTICAL?
Clean with soap and water cleaners only. Never use solvents on plastic parts.
Cleanliness of your elliptical and its operating environment will keep maintenance problems and service calls to a minimum. For this reason, Horizon Fitness recommends that the following preventive maintenance schedule be followed.
AFTER EACH USE (DAILY)
Turn off the elliptical by unplugging the power cord from the wall outlet
•Wipe down the elliptical with a damp cloth. Never use solvents, as they can cause damage to the elliptical.
•Inspect the power cord. Replace the power cord if damaged.
•Make sure the power cord is not underneath the elliptical or in any other area where it can become pinched or cut.
|
| To remove power from the elliptical, the power cord must be disconnected from |
| WARNING | |
| the wall outlet. | |
|
|
|
|
|
|
WEEKLY
Clean underneath the elliptical, following these steps:
•Turn off the elliptical
•Move the elliptical to a remote location.
•Wipe or vacuum any dust particles or other objects that may have accumulated underneath the elliptical.
•Return the elliptical to its previous position.
EVERY MONTH
•Inspect all assembly bolts and pedals on the machine for proper tightness.
•Clean any debris off of the pedal arm wheels and guide rails.
PARTS LIST
Please refer to EXPLODED DRAWING on previous page.
Item #: | Description: | Part #: | Description: |
AC1 | Console Mast Set (includes P07) | R08 | Nut |
AE1 | Pedal Arm(Includes E22) | R09 | Eye Bolt |
AG1 | Handlebar Set,Lower Right(Includes G13) | R10 | Washer |
AG2 | Handlebar Set,Lower Left(Includes G13) | R11 | Nut |
AG3 | Handlebar Set, Upper Right(Includes G09,G15,G16,G12,G18,G15,G20,G21,G22,G23,G24,G25) | R12 | Bearing |
AG4 | Handlebar Set, Upper Left(Includes G09,G15,G16,G12,G18,G15,G20,G21,G22,G23,G24,G25) | R13 | Nut |
AG6 | Bracket,Lower Handlebar | R14 | Washer |
AH1 | Lower Link Arm Right | R15 | Drive Belt |
AH2 | Lower Link Arm Left | R16 | Magnet |
AJ1 | Crank | R17 | Screw |
AN1 | Console Set | R18 | Resistance Cable |
B19 | Nut,Leveler | R19 | Resistance Motor |
B20 | Leveler | R20 | Nut |
B26 | End Cap,Frame | Z01 | Washer |
C07 | Water Bottle Holder | Z02 | Bolt |
C08 | Bolt | Z03 | Screw |
C09 | Cap,Pulse Grip | Z04 | Axle,Link Arm |
C13 | Washer | Z06 | Washer |
C14 | Washer | Z07 | Bolt |
C15 | Washer | Z08 | Washer |
C16 | Bolt | Z15 | Bushing |
C17 | Z16 | Nut | |
E08 | Roller Wheel Set (Includes E07,E09,E13) | Z17 | Bolt |
E09 | Screw | Z18 | Washer |
E10 | Nut | Z19 | Screw |
E11 | Bushing | Z22 | Bolt |
E12 | Cover, Pedal Arm,L/R | Z23 | Bolt |
E14 | Washer | Z24 | Bolt |
E15 | Pivot Block Set (Includes E11) | Z31 | Lock Washer |
E16 | Bolt | Z32 | Bolt |
E16 | Bolt | Z33 | Washer |
E17 | Washer |
|
|
E17 | Washer |
|
|
E18 | Cover,Roller Wheel |
|
|
E20 | Screw |
|
|
E21 | Washer |
|
|
E22 | Bushing |
|
|
E24 | Nut |
|
|
E25 | Bolt |
|
|
E25 | Bolt |
|
|
E26 | Washer |
|
|
E26 | Washer |
|
|
E27 | Washer |
|
|
G08 | Set Screw |
|
|
G09 | Cap,Handlebar |
|
|
G10 | Cover,Handlebar |
|
|
G11 | Cover,Handlebar |
|
|
G13 | Bushing |
|
|
G14 | Set Screw |
|
|
G30 | Washer |
|
|
G31 | Bolt |
|
|
G32 | Washer |
|
|
H13 | Cover,Link Arm,Right |
|
|
H14 | Cover,Link Arm,Left |
|
|
H21 | Foot Pad |
|
|
H22 | Bolts |
|
|
H23 | Cap,Lower Link Arm |
|
|
J05 | Disk,Large Side Cover |
|
|
J06 | Cap,Large Side Cover Disk |
|
|
J07 | Screw |
|
|
KIT | Hardware Pack |
|
|
KIT | Owner’s Manual |
|
|
L01 | Mobile Wheel |
|
|
L03 | Stabilizer,Side L/R |
|
|
L04 | Leveler |
|
|
L05 | Sleeve,Wheel Axle |
|
|
N09 | Bracket, Console |
|
|
P01 | Bracket,Resistance Motor |
|
|
P02 | Screw |
|
|
P03 | Screw |
|
|
P04 | Console Cable |
|
|
P05 | AC Adapter |
|
|
P06 | Bracket,Resistance Motor |
|
|
P07 | Grip Pulse with wires (includes attachment screws) |
|
|
Q01 | Side Cover,Right |
|
|
Q02 | Side Cover,Left |
|
|
Q03 | Top Cap |
|
|
Q04 | Cover,Frame,Front |
|
|
Q05 | Cover,Frame,Middle |
|
|
Q06 | Cover,Frame,Back |
|
|
Q07 | Bracket |
|
|
Q08 | Tinnamen Nut |
|
|
Q09 | Screw |
|
|
R03 | Pedal Axle Set (Includes R16,R07,R12,R04,R06,R02) |
|
|
R04 | Spacer Ring |
|
|
R05 | Drive Axle |
|
|
R07 |
|
|
31
IMPORTANT PRECAUTIONS INTRODUCTION
ASSEMBLY
BEFORE YOU BEGIN
ELLIPTICAL OPERATION
LIMITED TROUBLESHOOTING CONDITIONING WARRANTY & MAINTENANCE GUIDELINES
SXE7.7_Rev.1.6.indd | 8/16/07 11:02:02 AM |
