INTRODUCTION IMPORTANT PRECAUTIONS
ASSEMBLY
ASSEMBLY STEP 6
HARDWARE BAG 6 CONTENTS:
BOLT (H) | FLAT WASHER (L) | SPRING WASHER (M) |
25 mm | 8 mm | 8 mm |
Qty: 6 | Qty: 6 | Qty: 6 |
| A Open HARDWARE BAG 6. |
| B Align SUPPORT BAR with holes in |
| CONSOLE MAST and support bar |
| bracket as shown. |
SUPPORT | C Attach bottom of SUPPORT bar to |
BAR BRACKET | |
SUPPORT BAR | console mast using 2 Bolts (H), |
CONSOLE MAST | 2 SPRING WASHERS (M) and 2 FLAT |
BEFORE YOU BEGIN
Congratulations on choosing your treadmill! You’ve taken an important step in developing and sustaining an exercise program! Your treadmill is a tremendously effective tool for achieving your personal fitness goals. Regular use of your treadmill can improve the quality of your life in so many ways.
Here are just a few of the health benefits of exercise:
•Weight Loss
•A Healthier Heart
•Improved Muscle Tone
•Increased Daily Energy Levels
The key to reaping these benefits is to develop an exercise habit. Your new treadmill will help you eliminate obstacles that prevent you from exercising. Inclement weather and darkness won't interfere with your workout when you use your treadmill in the comfort of your home. This guide provides you with basic information for using and enjoying your new machine.
IMPORTANT PRECAUTIONS INTRODUCTION
ASSEMBLY
BEFORE YOU BEGIN
| washers (L). | |
BOLTS (H) | * Do not tighten bolts until step F. | |
SPRING WASHERS (M) | ||
| ||
FLAT WASHERS (L) | D To attach top of SUPPORT BAR, insert | |
| 1 Bolt (H), 1 SPRING WASHER (M) and | |
| 1 FLAT washer (L) through support | |
FLAT WASHER (L) | bar bracket and support bar as |
LOCATION OF THE TREADMILL
Place the treadmill on a level surface. There should be 6 feet of clearance behind the treadmill, 3 feet on each side and one foot in front for folding and the power cord. Do not place the treadmill in any area that will block any vent or air openings. The treadmill should not be located in a garage, covered patio, near water or outdoors.
1 foot
BEFORE YOU BEGIN
TREADMILL OPERATION
SPRING WASHER (M) | shown. |
BOLT (H) |
|
| E | Repeat on other side. |
SUPPORT BAR BRACKET | F | IMPORTANT: Completely tighten ALL |
| bolts from steps | |
SUPPORT BAR |
| |
|
| |
CONSOLE MAST |
|
|
| G | Connect power plug to the treadmill |
|
| and connect the cord to a power outlet. |
|
| The POWER switch is located next to |
WARNING
DO NOT STAND ON THE BELT
While you are preparing to use the treadmill, do not stand on the belt. Place your feet on the side rails before starting the treadmill. Start walking on the belt only after the belt has begun to move. Never start the treadmill at a fast running speed and attempt to jump on!
3 feet | 3 feet |
6 feet
TREADMILL OPERATION
CONDITIONING TROUBLESHOOTING LIMITED
GUIDELINES & MAINTENANCE WARRANTY
14
POWER SWITCH CIRCUIT BREAKER | the power cord. Flip this switch to the | |
'ON' position, so that the switch is lit. | ||
| ||
POWER PLUG | You will hear a beep and the console will | |
| ||
| light up. | |
| H Before the first use, lubricate the | |
| treadmill deck by following the | |
| instructions in the Maintenance section. |
YOU’RE FINISHED!
SAFETY KEY
Your treadmill will not start unless the safety key is placed in position. Attach the clip end securely to your clothing. This safety key is designed to cut the power to the treadmill if you should fall. Check the operation of the safety key every 2 weeks.
NEVER USE THE TREADMILL WITHOUT SECURING THE SAFETY KEY CLIP TO
WARNING YOUR CLOTHING. PULL ON THE SAFETY KEY CLIP FIRST TO MAKE SURE IT WILL NOT COME OFF YOUR CLOTHING.
15
LIMITED TROUBLESHOOTING CONDITIONING WARRANTY & MAINTENANCE GUIDELINES
T901_Rev.2.0.indd | 9/10/08 11:15:51 AM |
