Manuals / Brands / Computer Equipment / Printer / HP / Computer Equipment / Printer

HP 9800 CAUTION, 2.7 DATA CABLE INSTALLATION, 2.6 USING AN EXTERNAL SPEAKER, Figure 2-6Data Cable Installation (-001Cable Shown)

1 127

Download 127 pages, 13.41 Mb

INSTALLATION

Data Pigtail Cable	Strain Relief	Two User-Definable Wires

Accessory

Pigtail Cable

J701 J301

Figure 2-6 Data Cable Installation (-001 Cable Shown)

installed. Then install the mounting bracket using the included self-tapping screws or other screws if desired.

2.Install the control unit in the bracket using the included knobs and vulcanized washers (the washers are installed between the bracket and control unit).

3.Install the included microphone hanger in a conve- nient location using the included sheet metal screws or other screws. For proper operation of functions such as the monitor mode and scan, the hanger must be connected to chassis ground. If required, ground the hanger using the included ground wire.

2.6 USING AN EXTERNAL SPEAKER

Power output with the internal 8-ohm speaker in the front panel or remote control unit is approximately 3 watts. For up to 5 watts of power, a 4.7-ohm external speaker can be used. This speaker is plugged into the external speaker jack on the back of the transceiver.

This is a standard 1/8”, two-conductor phone jack. The

internal speaker is automatically disabled when an external speaker is used.

The impedance of the external speaker must not be less than 4.0 ohms. Using a speaker with an impedance less than 4.0 ohms could result in audio amplifier U306 overheating and does not provide 5 watts of power. Therefore, to allow for tolerances, a speaker with a nominal impedance of 4.7 ohms is recom- mended. The E.F. Johnson remote speaker listed in Figure 2-1or Table 1-3meets this requirement. This speaker has a 6-ft cable, and in some applications (such as remote mounting) an extension cable may be required to connect it to the transceiver.

2.7 DATA CABLE INSTALLATIONCAUTION

DO NOT apply power a transceiver that has one of the data cables installed without first properly terminating the wires of that cable. These wires carry differing potentials and transceiver damage may result if they inadvertently contact each other.

	February 2001
2-7	Part No. 001-9800-001

Contents

25 or 40 Watts (UHF); 15 or 30 Watts (800/900 MHz) 13.6 VDC Part No 13.6 VDC 25 or 40 Watts, UHF 15 or 30 Watts, 800/900 MHz Part No. 242-984x-2xx(UHF) Part No. 242-988x-2xx(800 MHz) TABLE OF CONTENTS 1 GENERAL INFORMATION 3 CIRCUIT DESCRIPTION 2 INSTALLATION TABLE OF CONTENTS (CONT’D) 4 SERVICING 5 PARTS LIST 6SCHEMATIC DIAGRAMS AND COMPONENT LAYOUTS LIST OF TABLES LIST OF FIGURES SECTION 1 GENERAL INFORMATION 1.3 PART NUMBER BREAKDOWN Table 1-1Part Number Breakdown 1.4 TRANSCEIVER IDENTIFICATION Table 1-2Identification Number Breakdown Type 1.5 ACCESSORIES Table 1-398xx Accessories Accessory Cable Data/Accessory Cable Desktop Accessories 1.6 PRODUCT WARRANTY 1.7 FACTORY CUSTOMER SERVICE 1.8 FACTORY RETURNS 1.9 REPLACEMENT PARTS 1.10 INTERNET HOME PAGE UHF 984x SPECIFICATIONS 800 MHz 988x SPECIFICATIONS 900 MHz 989x SPECIFICATIONS SECTION 2 INSTALLATION 2.2 MOUNTING THE TRANSCEIVER WARNING Item Figure 2-2Remote Mount Installation Components 2.3 POWER CABLE INSTALLATION Figure 2-3Accessory Cable Installation 2.4 ACCESSORY CABLE INSTALLATION Function Figure 2-4Accessory Cable Connector Figure 2-5R170 Location Diagram Sw Bat Out (pin 2) Horn Alert (pin 4) - See Section Ignition Sense (pin 6) - See Section Output D (pin 7) 2.5 REMOTE CONTROL UNIT INSTALLATION Figure 2-6Data Cable Installation (-001Cable Shown) 2.6 USING AN EXTERNAL SPEAKER 2.7 DATA CABLE INSTALLATION CAUTION Table 2-1Data Cable Wire Chart J301 Pin No Wire Color 2.8 KEY CAP KITS EMER F1 F2 F3 SCAN SCAN BKLHT MSG HORN SECTION 3 CIRCUIT DESCRIPTION POWER DISTRIBUTION (ALL MODELS) 3.2 POWER DISTRIBUTION AND SWITCHING Figure 3-1Power Distribution and Switching Figure 3-2Power On-OffControl Circuit AUDIO/LOGIC DESCRIPTION (ALL MODELS) 3.3 AUDIO/LOGIC BOARD DIGITAL CIRCUIT VRH/VRL PE0 PE1 PE2 PE3 PA0 PA1 PA2 PA3 PA4/PA5 3.4 RECEIVE AUDIO/DATA PROCESSING Figure 3-3Audio and Data Processing Circuitry Block Diagram 3.5 TRANSMIT AUDIO/DATA PROCESSING 3.6 DISPLAY BOARD DISPLAY DESCRIPTION 3.7SYNTHESIZER CIRCUIT DESCRIPTION (UHF MODELS) UHF SYNTHESIZER DESCRIPTION 4-3Figure Diagram Block RF Models) (UHF DESCRIPTION SYNTHESIZER UHF DESCRIPTION CIRCUIT Page Page Figure 3-5Synthesizer Chip U804 Block Diagram 3.8RECEIVER CIRCUIT DESCRIPTION (UHF MODELS) UHF RECEIVER DESCRIPTION Figure 3-6Limiter/Detector U201 Block Diagram UHF TRANSMITTER DESCRIPTION 3.9TRANSMITTER CIRCUIT DESCRIPTION (UHF MODELS) Page Page 800/900 MHz SYNTHESIZER DESCRIPTION 3.10SYNTHESIZER CIRCUIT DESCRIPTION (800/900 MHz MODELS) 7-3Figure Models) MHz (800/900 DESCRIPTION SYNTHESIZER MHz 800/900 Normal Mode Talk-AroundMode Page Page Page 800/900 MHz RECEIVER DESCRIPTION 800/900 MHz TRANSMITTER DESCRIPTION 3.12TRANSMITTER CIRCUIT DESCRIPTION (800/900 MHz MODELS) Page Page Page SECTION 4 SERVICING American EIA Standard Japanese EIA Standard (pF) Color Multi Figure 4-1Simplified Synthesizer Block Diagram 4.3 SYNTHESIZER TROUBLESHOOTING Table 4-2SMD Inductor Identification Mode Supply Voltage Output Level Control Voltage VCO RF In (pin 6) Overall Div No. (K) = VCO freq ÷ “A” Divide No “N” Divide No Fractional-NDiv No. = (Fraction K) x 4.4RECEIVER SERVICING SECTION 5 PARTS LIST FRONT PANEL ASSEMBLY AND MECHANICAL PARTS FRONT PANEL ASSEMBLY AND MECHANICAL PARTS (CONT’D) UHF RF AND PA BOARDS UHF RF AND PA BOARDS (CONT ’D) Page Page Page Page Page Page Page Page Page Page Page Page Page 800/900 MHZ RF AND PA BOARDS 800/900 MHz RF AND PA BOARDS (CONT ’D) Page Page Page Page Page AUDIO/LOGIC BOARD (ALL MODELS) AUDIO/LOGIC BOARD (CONT’D) Page Page Page 9800-SERIESRADIO MOUNTING KIT 9800-SERIESREMOTE MOUNTING KIT DC POWER CABLE AND HARDWARE KIT PART NO. 023-9800-410(10 Ft) PART NO. 023-9800-422(22 Ft) FRONT PANEL EXPLODED VIEW FRONT AND TOP MECHANICAL PARTS BOTTOM MECHANICAL PARTS REMOTE TRANSCEIVER MECHANICAL PARTS REMOTE CONTROL UNIT MECHANICAL PARTS SECTION 6 SCHEMATIC DIAGRAMS AND COMPONENT LAYOUTS TRANSISTOR AND DIODE BASING DIAGRAMS Page Page CAUTION: INTERFACE BOARD LAYOUT INTERCONNECT SCHEMATIC DISPLAY BOARD TOP VIEW DISPLAY BOARD BOTTOM VIEW PROGRAMMING CABLE (P.N. 597-2002-200) RPI (P.N. 023-9800-000)BOARD LAYOUT RPI (P.N. 023-9800-000)SCHEMATIC RF BOARD COMPONENT LOCATOR GUIDE (UHF) UHF RF BOARD COMPONENT LOCATOR GUIDE (CONT’D) ’D) RF BOARD COMPONENT LOCATOR GUIDE (800/900 MHZ) Page Page Page Page RF BOARD SCHEMATIC (REVISED 430-470MHZ) PA BOARD SCHEMATIC (25W, 430-470MHZ)