SCSI Port Control Mode page
NOTE: This page is supported for SCSI drives only, from Gen 3 onwards.
Normal page
If the Port Control mode page (19h) is requested via the MODE SENSE command with the Sub- Page code set to zero, the following data will be returned:
|
| 7 |
| 6 | 5 | 4 | 3 | 2 | 1 | 0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0 | PS (0) |
| SPF(0) |
|
| Page Code {19h} |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| 1 |
|
|
|
| Page Length {06h) |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |
| 2 |
|
| Reserved (0) |
|
| Protocol Identifier (1h) |
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| 3 |
|
|
|
| Reserved (0) |
|
|
|
| |
| 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Synchronous Transfer Timeout (0) |
|
|
| ||||
| 5 |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| Reserved (0) |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
| Protocol Identifier |
| 1 The protocol to which this mode page applies is SPI SCSI. |
Synchronous Transfer Timeout 0 Synchronous Transfer Timeout is disabled.
|
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
|
|
|
|
|
|
|
|
|
|
| 0 | PS (0) | SPF(0) |
|
| Page Code {19h} |
|
| |
|
|
|
|
|
|
|
|
|
|
| 1 |
|
|
| Subpage Code |
|
|
| |
| 2 |
|
|
|
|
|
|
|
|
|
|
|
| Page Length |
|
|
| ||
| 3 |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
| 4 |
|
|
| Reserved (0) |
|
|
| |
|
|
|
|
|
|
|
|
| |
| 5 |
| Reserved (0) |
|
| Protocol Identifier (01h) |
| ||
| 6 |
|
|
|
|
|
|
|
|
|
|
| Protocol Specific Mode Parameters |
|
| ||||
| n |
|
|
|
| ||||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
The following
•Margin Control (01h) — static data
•Saved Training Configuration Values (02h) — static data
•Negotiated Settings (03h) — dynamic data
•Report Transfer Capabilities (04h) — static data
Commands
MODE SELECT 15h/55h 87