HP UX System Management Software pax, pax, tar, pax, pax, tar, (1), PDC, PXE, tar, boot, cpio, DHCP, boot, depot, bundle, system, reboot, kernel, before, bundles, bundles, archive, cpio(1)

optional	With 11i v3, software bundles that are not installed with HP-UX by default. You must select
	these bundles before installation. Ignite-UXis an example of an optional software bundle.
P
partition	A portion of a disk device that appears to volume managers, file systems, and other OS software
	as a disk device. Partitions allow different portions of a disk to hold content needed for boot,
	OS file systems, diagnostic tools, and other information.
pax	An HP-UX file archiving command that extracts, lists, and writes member files to an archive.
	Ignite-UXuses pax to produce tar, cpio, and pax formatted archives. See pax(1),tar(1), and
	cpio(1).
PDC	See Processor Dependent Code.
persistent DSF	A DSF conforming to the naming model introduced in HP-UX 11i v3 to support agile addressing.
	The device file name contains an instance number, such as /dev/disk/disk#, and the minor
	number has no hardware path information.
physical location	Device identifier that uses information such as cabinet, bay, and LUN ID to indicate where the
	device is actually located. Used to indicate a specific device independent of I/O path changes.
pkg_rec_depot	An Ignite-UXcommand that repackages the Ignite-UXproduct into a depot on an Ignite-UX
	server in order to distribute Ignite-UXsoftware to client systems that use the Ignite-UX server for
	network recovery. See pkg_rec_depot(1M).
print_manifest	An Ignite-UXcommand that displays a manifest of the system it is run on. It can either display
	the original manifest, or gather information about the current system when it runs. See
	print_manifest(1M).
processor	The firmware that implements all processor-dependent functionality including initialization
dependent code	and self-test of the processor. Upon completion, it loads and transfers control to the initial system
	loader. Firmware behavior varies depending on the hardware series. See pdc(1M).
product	In SD-UX, a collection of filesets, individual filesets, or both.
PXE	Stands for preboot execution environment. A protocol built on top of DHCP on HP-UX
	Itanium-based systems used to request boot services from a server in order to load the operating
	system.
R
reboot	To stop all running code including the kernel, restart a computer, and boot the system. See
	shutdown(1M) and reboot(1M).
RECCMDS	A compressed tar archive of commands required for expert recovery on PA-RISC systems.
RECCMDSIA	A compressed tar archive of commands required for expert recovery on Itanium-based systems.
recommended	With 11i v3, software bundles that are recommended and should be installed with HP-UX
	because they fulfill required software dependencies, if any exist. You can deselect the bundles
	before installation.
recovery	See system recovery.
recovery archive	An archive that retains host specific customizations from the system. See archive.
recovery image	A system-specific snapshot of a system that contains hostname, IP address, networking
	information, all files and directories essential to bringing up a functional system, as well as
	optionally including specified data on a disk, volume group, file, or directory basis. It is created
	with make_[tapenet]_recovery.
recovery shell	See expert recovery.
registered client	A client system that has its MAC address registered with the server in order to always boot to the
	same assigned IP address. For PA-RISC systems, the client’s MAC address is assigned to an IP
	address in the /etc/opt/ignite/instl_boottab or /etc/bootptab file. For
	Itanium-based systems, the default is to use the /etc/bootptab file.
required	With 11i v3, software and network driver bundles that are required and always installed with
	HP-UX. Software in this category cannot be deselected.

39