Assembly Seat Installation | Huffy M0012 instruction

Assembly

Seat Installation

Attach Seat to Seat Post: (pre-assembled on some models)

•Loosen nuts on seat clamp (A) and rotate Seat (8) into riding position.

•Put the seat post (9) fully through the seat clamp (A).

•Tighten the Seat Clamp so the seat stays on the seat post.

•If the Seat Clamp has a nut on each side, tighten both nuts equally.

8A

9

fig 06

CAUTION: If you accidentally drop the seat post into the seat tube, it may be difﬁcult to remove it.

•Point the Seat (8) forward and put the Seat Post (9) into the Seat Tube (B) (ﬁgs 07, 08).

WARNING: To prevent the seat com- ing loose and possible loss of control, the “MIN-IN” (minimum insertion) mark (C) on the seat post must be below the top of the Seat Tube.

Tighten the quick release lever:

•Move the Quick Release Lever (D) to the “open” position so the word “open” is pointing away from the Seat Post Clamp (E).

NOTE: The words “open” and “close” are on opposite sides of the quick release lever.

8	C	B
		B

9	B
9
	C

fig 07

		9
	F	B
	F	E
		E

D

fig 08

16

Image 16

Huffy M0012 manual Assembly Seat Installation, Attach Seat to Seat Post pre-assembled on some models

Contents

For Mountain Bikes Your Bike Fitting the Rider to the Bicycle Your Bike Owner’s Bicycle Identiﬁcation RecordModel / Serial Number Purchase Date Model Name Rules of the Road Meanings of WarningsIf you must ride at night or at time of poor visibility Use extra caution in wet weather Your Bike Owner’s Responsibility Parts Assembly View Parts View Parts List Parts Assembly ListDescription Assembly Introduction Assembly Small Adjustable WrenchTools Needed Flat-blade Screwdriver Handlebar and Stem Installation Quill Style Stem Threadless Style Stem Install the Front Wheel Assemble the Front Wheel to the Fork AssemblyLoosen the Front Brakes Re-attache Front Brake Cable Re-attach Front Brake Cable Assembly Setting Up the Handlebars To test the tightness of the stem Testing Stem and Handlebar TightnessTo test the tightness of the handlebar clamp Attach Seat to Seat Post pre-assembled on some models Assembly Seat InstallationTighten the quick release lever Testing Seat Clamp and Post Clamp Tightness To test the tightness of the seat clamp and the post clampIf the seat moves in the Seat Clamp a ﬁg If the Seat Post 9 moves in the Seat Tube B Assembly Pedal Installation Tighten the pedals ﬁg Reﬂector Brackets Installation Installing Derailleur Guard on some models Maintenance Brake System Test the tightness of each Brake Shoe Maintenance Final Brake Adjustment Before Riding Stretching the cable ﬁgCheck tightness of the cantilever mounting Bolt a Center brake shoes on rim Maintenance Final Brake Adjustment Put the brake shoes the correct distance from the rim Test the tightness of the cable clamp ﬁg MaintenanceTest the travel of each brake lever Maintenance Parts of the Shift System Shift SystemOperation Operate the shift system as follows Maintenance Shift System These are the higher gear combinations Front Derailleur Adjustments Perform the Rear Derailleur Adjustments if Maintenance Rear Derailleur Adjustments Adjust the Index Shift System ﬁg Maintenance Three-Piece Cranks various models Maintenance Suspension Frame various models AdjustmentTo change the suspension Maintenance Tires Inﬂating the Tires Repair and Service Maintenance Lubrication What When How Lubrication Table Maintenance Reﬂectors Inspection of the BearingsHead Tube Bearings Crank Bearings Warranty Huffy Corporation Limited Warranty What does this Limited Warranty cover?What must you do to keep the Limited Warranty in effect? What is not covered by this Limited Warranty? Warranty For how long does this Limited Warranty last?How do you get service? What will Huffy do? Always Wear Your Helmet When Riding this Product