MAINTENANCE

Throttle lockout

•Make sure the throttle control is locked at the idle setting when the throttle lockout is released. (95)

•Press the throttle lockout and make sure it returns to its original position when you release it. (96)

•Check that the throttle control and throttle lockout move freely and that the return springs work properly.

(97)

•Start the chain saw and apply full throttle. Release the throttle control and check that the chain stops and remains stationary. If the chain rotates when the throttle control is in the idle position you should check the carburetor idle adjustment.

Chain catcher

Check that the chain catcher is not damaged and is firmly attached to the body of the chain saw. (98)

Right hand guard

Check that the right hand guard is not damaged and that there are no visible defects, such as cracks. (11)

Vibration damping system

Regularly check the vibration damping units for cracks or deformation. Make sure the vibration damping units are securely attached to the engine unit and handle unit. (99)

Stop switch

Start the engine and make sure the engine stops when you move the stop switch to the stop setting. (53)

NB! The start/stop switch automatically returns to run position. In order to prevent unintentional starting, the spark plug cap must be removed from the spark plug when assembling, checking and/or performing maintenance.

Muffler

Never use a machine that has a faulty muffler.

Regularly check that the muffler is securely attached to the machine. (100)

Some mufflers are equipped with a special spark arrestor screen. If your machine has this type of muffler, you should clean the screen at least once a week.This is best done with a wire brush. A blocked screen will cause the engine to overheat and may lead to serious damage.

Note! The screen must be replaced if it is damaged. If the screen is blocked the machine will overheat and this will cause damage to the cylinder and piston. Never use a machine with a muffler that is in poor condition. Never use a muffler if the spark arrestor screen is missing or defective. (13)

The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.

Starter

WARNING! When the recoil spring is

!wound up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury.

Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective gloves.

Replacing the starter cord

•Loosen the screws that hold the starter against the crankcase and remove the starter. (101)

•Pull out the cord approx. 30 cm and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards. (102)

•Undo the bolt in the centre of the pulley and remove the drive disc (A), drive disc spring (B) and the pulley

(C). Insert and secure a new starter cord in the starter pulley. Wind approx. 3 turns of the starter cord on the starter pulley. Fit the starter pulley so that the end of the recoil spring (D) hooks into the starter pulley. Now assemble the drive disc spring, drive disc and the bolt in the centre of the pulley. Carry the starter cord through the hole in the starter housing and the starter handle. Tie a good knot on the starter cord. (103)

1153136-49 Rev.2 2010-04-08

English – 27

Page 26 Page 28
Page 27
Image 27
Husqvarna 1153136-49 manuel dutilisation Muffler, Starter, Replacing the starter cord
Page 26 Page 28

1153136-49 specifications

The Husqvarna 1153136-49 is a reliable and high-performance chainsaw specifically designed for homeowners and occasional users who seek both power and ease of use. Its construction reflects Husqvarna's reputation for quality and innovation, making it a preferred choice among enthusiasts and those needing practical tools for yard and garden maintenance.

One of the standout features of the 1153136-49 is its powerful engine. It is equipped with a sturdy and efficient 50.2cc X-Torq engine, which delivers excellent power output while minimizing fuel consumption and emissions. This means users can enjoy extended operation time with reduced environmental impact, which is increasingly important in today’s eco-conscious world.

The chainsaw boasts an impressive cutting length, making it suitable for a variety of tasks, from pruning branches to cutting firewood. With a bar length of 18 inches, it provides the versatility needed for light to medium-duty jobs, enabling users to tackle projects around their homes and gardens with ease.

Husqvarna has designed the 1153136-49 with user comfort and safety in mind. It features an ergonomic handle with a soft grip that reduces vibrations, allowing for longer periods of use without discomfort. The chainsaw also includes an advanced anti-vibration system, ensuring a smoother operation that minimizes strain on the user’s hands and arms.

Safety is paramount when using a chainsaw, and Husqvarna has integrated several key safety features in the 1153136-49. It comes with a chain brake that stops the chain in case of kickback, as well as low kickback chains that further enhance user safety during operation. The quick-release air filter simplifies maintenance and ensures optimal engine performance.

Another innovative feature is the tool-less chain tensioning system, which allows for easy adjustments on the go, ensuring that the chain remains tight and secure during use. This design not only saves time but also enhances overall safety.

In conclusion, the Husqvarna 1153136-49 is a powerful, efficient, and user-friendly chainsaw packed with features that enhance performance and safety. It is an ideal choice for homeowners and anyone looking to manage their outdoor tasks effectively. With a strong engine, ergonomic design, and safety features, it represents a smart investment for maintaining gardens and outdoor spaces.
Top Page Image Contents