Drive, Axle Shaft, Thrust Washer, Clik PIN

REPAIR PARTS

DRIVE

SNOWTHROWER-MODELNO.1330SB-XLSB(96193004100),PRODUCTNO.9619300-41

	7
		4
8	2	3
8	2
7	1
	1
	9

	5	3
	5	4
		4

601.03.003-A

KEY	PART		DESCRIPTION
NO.	NO.		DESCRIPTION
1	532	40 43-08	AXLE SHAFT
2	532	18 77-94	SPACER
3	532	17 46-97	THRUST WASHER
4	532	17 98-30	BEARING

5532 14 63-15 SCREW 5/16−18 X .625

6817 49 05-08 BOLT 5/16−18 X .500

7	532 15 54-43	CLIK PIN
8	874 78 06-32	SCREW 3/8−16 X 2.00
9	873 80 06-00	NUT 3/8−16

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 31

Page 31

Image 31

Husqvarna 1330SB-XLSB owner manual Drive, Axle Shaft, Thrust Washer, Clik PIN

Contents

1330SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Rotator Head Mounting Chute Deflector Remote ControlParts Packed Separately in Carton EXT RA Shear Bolts and Nuts Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Install Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower Primer Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See Fig Check Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Snow Thrower CleaningEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Other Storage Troubleshooting Auger Housing / Impeller Assembly Repair Parts KEY Part Description Auger Assembly 30 RH Auger Assembly 30 LH Skid Plate Auger Ball Bearing CARRIAGEBOLT5/16−18X.750 Weight BAR 532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP Rivet Rotator Pivot Bracket 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Head Handles POP Rivet 1/8 01.12.002-C 532 17 86-66 Halogen Headlight Grip Switch532 42 13-51 Console Panel Gray 532 42 14-48 Headlight Bezel Gray Clik PIN DriveAxle Shaft Thrust Washer 921 01.02.002-F Clevis PIN 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Idler Pulley 01.01.001-B Bottom PAN Chassis / Engine / PulleysEngine Model Frame Steer Cable Bracket RH Wheel Assembly LHWheels Steer Cable Bracket LH Axle Lobe CoverWheel Lobe Spring Retainer PIN Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY BAG of Parts 532 18 10-35 DECAL, DANGER, Deflector Decals532 18 37-30 DECAL, Remote Deflector Warranty Statement

REPAIR PARTS

DRIVE

KEY

AXLE SHAFT

THRUST WASHER

BEARING

CLIK PIN