Chassis / Engine / Pulleys, Engine Model

REPAIR PARTS

CHASSIS / ENGINE / PULLEYS

SNOWTHROWER-MODELNO.1330SB-XLSB(96193004100),PRODUCTNO.9619300-41

5 4

01.00.021-B

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
- -	- - - - - -	B&S ENGINE MODEL
		21M414-1182-E1
1	532 41 53-40	FRAME
2	532 40 37-32	BOTTOM PAN
3	532 40 38-70 ENGINE MOUNT PLATE
4	532 15 04-06	BOLT 3/8−16

5532 15 00-78 SCREW 5/16−18 X .750

6532 18 44-71 SCREW 10−24 X .625

01.04.002-B

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 40 91-61	COVER ASSEMBLY
2	532 17 88-13	PULLEY

3532 19 23-83 TRACTION BELT

4532 40 80-19 IMPELLER BELT

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 35

Image 35

Husqvarna 1330SB-XLSB Chassis / Engine / Pulleys, Engine Model, Frame, Bottom PAN, 532 40 38-70 Engine Mount Plate

Contents

1330SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Rotator Head Mounting Chute Deflector Remote ControlParts Packed Separately in Carton EXT RA Shear Bolts and Nuts Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Check Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower Primer Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See Fig Check Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Engine CleaningSnow Thrower Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Other Storage Troubleshooting Auger Housing / Impeller Assembly Repair Parts KEY Part Description Auger Assembly 30 RH Auger Assembly 30 LH Skid Plate Auger Ball Bearing CARRIAGEBOLT5/16−18X.750 Weight BAR 532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP Rivet Rotator Pivot Bracket 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Head Handles POP Rivet 1/8 01.12.002-C 532 17 86-66 Halogen Headlight Grip Switch532 42 13-51 Console Panel Gray 532 42 14-48 Headlight Bezel Gray Clik PIN DriveAxle Shaft Thrust Washer 921 01.02.002-F Clevis PIN 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Idler Pulley 01.01.001-B Bottom PAN Chassis / Engine / PulleysEngine Model Frame Steer Cable Bracket RH Wheel Assembly LHWheels Steer Cable Bracket LH Axle Lobe CoverWheel Lobe Spring Retainer PIN Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY BAG of Parts 532 18 37-30 DECAL, Remote Deflector Decals532 18 10-35 DECAL, DANGER, Deflector Warranty Statement

Husqvarna 1330SB-XLSB owner manual Chassis / Engine / Pulleys, Engine Model, Frame, Bottom PAN

Models: 1330SB-XLSB

REPAIR PARTS

CHASSIS / ENGINE / PULLEYS

KEY

B&S ENGINE MODEL

FRAME

BOTTOM PAN

532 40 38-70 ENGINE MOUNT PLATE

KEY

PULLEY