Cover, Wheel Lobe, Spring, Axle Lobe | Husqvarna 1330SB-XLSB

REPAIR PARTS

WHEELS

SNOWTHROWER-MODELNO.1330SB-XLSB(96193004100),PRODUCTNO.9619300-41

2

									17		23
						20					23
						20				19
				17	18	16					22	7
						15	18				22	7
						15	18				9	8
				16		24					10
				20		23		21			11
				19		22
				19							12
				21							12
											14
								14 13			13
						11		14 13
					10			12
2				8	9
2				7
	3	4	5	6
2	1 01.15.001-A
				KEY	PART				DESCRIPTION
				NO.	NO.				DESCRIPTION
				1	532 40 51-61					COVER

2532 18 44-71 SHOULDER SCREW

3812 00 00-45 RETAINER RING

4532 19 21-26 WHEEL DRIVER

5532 18 24-66 RETAINER RING

6	532 18 76-22	WHEEL LOBE
7	532 19 49-41 CLUTCH SLIDE
8	532 17 91-39	SPRING
9	532 18 92-82	SQUARE KEY
10	532 19 49-40	AXLE LOBE

11532 17 46-97 THRUST WASHER

12532 19 95-19 STEERING YOKE

13532 18 41-97 STEERING BRACKET

14817 49 05-08 SCREW 5/16−18 X .50

15532 19 95-11 PIVOT BRACKET

16	532 19 95-18 BELLCRANK

17532 18 18-47 BELLCRANK PIN

18817 60 04-06 SCREW 1/4−20 X .375

19532 40 50-77 STEERING LINK

20	532 70 02-79	RETAINER
21	532 08 51-79	RETAINER
22	532 19 38-85	SPRING
23	532 18 20-15	LEVER PIN
24	532 19 95-12 PIVOT BRACKET

		3	2
	4	3	1
6	5

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

37

Image 37

Husqvarna 1330SB-XLSB owner manual Cover, Wheel Lobe, Spring, Axle Lobe, Lever PIN

Contents

1330SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlEXT RA Shear Bolts and Nuts Rotator Head Mounting HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper Handle Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Install Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEY Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See Fig Scraper BAR See Fig Before Starting the EngineTo USE Drift Cutters See Fig Check Engine OIL Level See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Snow Thrower CleaningEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig Other Storage Troubleshooting Auger Housing / Impeller Assembly Repair Parts KEY Part Description Auger Assembly 30 RH Auger Assembly 30 LH Skid Plate Auger Ball Bearing CARRIAGEBOLT5/16−18X.750 Weight BAR Knob Black Control Panel / Discharge ChutePOP Rivet 532 42 17-28 Shield Retainer Strap Cable Assembly Gray 532 42 11-60 LEVER/CABLE Rotator Assembly GrayRotator Head Rotator Pivot Bracket Handles POP Rivet 1/8 01.12.002-C 532 42 13-51 Console Panel Gray Grip Switch532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen Headlight Axle Shaft DriveThrust Washer Clik PIN 921 01.02.002-F 532 18 77-86 Traction Idler ARM 532 18 04-78 Engine Traction PulleyIdler Pulley Clevis PIN 01.01.001-B Engine Model Chassis / Engine / PulleysFrame Bottom PAN Wheels Wheel Assembly LHSteer Cable Bracket LH Steer Cable Bracket RH Wheel Lobe CoverSpring Axle Lobe KEY Part Description 532 19 30-71 Safety Ignition KEY Power CordBAG of Parts Retainer PIN 532 18 10-35 DECAL, DANGER, Deflector Decals532 18 37-30 DECAL, Remote Deflector Warranty Statement