01.12.002-C

REPAIR PARTS

HANDLES

SNOWTHROWER-MODELNO.1330SB-XLSB(96193004100),PRODUCTNO.9619300-41

11 2

8 5

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 42 17-63 IMPELLER ROD ASSEMBLY

2532 18 04-85 TRACTION ROD ASSEMBLY

3532 18 77-82 SHIFTER ROD TOP

4532 18 77-84 SHIFTER ROD BOTTOM

5532 18 04-47 SPRING SLEEVE

6532 19 20-91 SPRING SLEEVE

7532 17 86-69 IMPELLER SPRING

8532 18 09-26 TRACTION SPRING

9872 27 05-06 CARRIAGE BOLT 5/16−18 X .750

10	532 15 53-77	NUT 5/16−18
11	532 16 96-75	RETAINER

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 29

Page 29

Image 29

Husqvarna 1330SB-XLSB owner manual 01.12.002-C

Contents

1330SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlEXT RA Shear Bolts and Nuts Rotator Head Mounting HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper Handle Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Check Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEY Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See Fig Scraper BAR See Fig Before Starting the EngineTo USE Drift Cutters See Fig Check Engine OIL Level See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine CleaningSnow Thrower To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig Other Storage Troubleshooting Auger Housing / Impeller Assembly Repair Parts KEY Part Description Auger Assembly 30 RH Auger Assembly 30 LH Skid Plate Auger Ball Bearing CARRIAGEBOLT5/16−18X.750 Weight BAR Knob Black Control Panel / Discharge ChutePOP Rivet 532 42 17-28 Shield Retainer Strap Cable Assembly Gray 532 42 11-60 LEVER/CABLE Rotator Assembly GrayRotator Head Rotator Pivot Bracket Handles POP Rivet 1/8 01.12.002-C 532 42 13-51 Console Panel Gray Grip Switch532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen Headlight Axle Shaft DriveThrust Washer Clik PIN 921 01.02.002-F 532 18 77-86 Traction Idler ARM 532 18 04-78 Engine Traction PulleyIdler Pulley Clevis PIN 01.01.001-B Engine Model Chassis / Engine / PulleysFrame Bottom PAN Wheels Wheel Assembly LHSteer Cable Bracket LH Steer Cable Bracket RH Wheel Lobe CoverSpring Axle Lobe KEY Part Description 532 19 30-71 Safety Ignition KEY Power CordBAG of Parts Retainer PIN 532 18 37-30 DECAL, Remote Deflector Decals532 18 10-35 DECAL, DANGER, Deflector Warranty Statement