Handles

REPAIR PARTS

SNOWTHROWER-MODELNO.1330SB-XLSB(96193004100),PRODUCTNO.9619300-41

8 4 7

9 9

7 6

12	01.08.012-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 41 55-39 CONTROL PANEL

2532 42 17-06 CONTROL LEVER LH

3532 42 17-07 CONTROL LEVER RH

4532 41 55-46 TRACTION ROD ARM

5532 42 14-92 IMPELLER ROD ARM

6532 41 26-77 INTERLOCK ROD

7	532 41 26-80	SPACER
8	532 16 96-75	RETAINER
9	817 06 04-08 SCREW 1/4−20 X .50
10	532 41 42-80	KNOB BLACK
11	532 41 42-81	KNOB RED
12	532 17 88-99	HANDLE KNOB
13	819 13 13-16	WASHER 3/8
14	872 12 06-18 CARRIAGE BOLT 3/8−16 X 2.25

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 27

Page 27

Image 27

Husqvarna 1330SB-XLSB owner manual Handles

Contents

1330SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Rotator Head Mounting Chute Deflector Remote ControlParts Packed Separately in Carton EXT RA Shear Bolts and Nuts Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower Primer Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See Fig Check Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Cleaning Snow ThrowerEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Other Storage Troubleshooting Auger Housing / Impeller Assembly Repair Parts KEY Part Description Auger Assembly 30 RH Auger Assembly 30 LH Skid Plate Auger Ball Bearing CARRIAGEBOLT5/16−18X.750 Weight BAR 532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP Rivet Rotator Pivot Bracket 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Head Handles POP Rivet 1/8 01.12.002-C 532 17 86-66 Halogen Headlight Grip Switch532 42 13-51 Console Panel Gray 532 42 14-48 Headlight Bezel Gray Clik PIN DriveAxle Shaft Thrust Washer 921 01.02.002-F Clevis PIN 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Idler Pulley 01.01.001-B Bottom PAN Chassis / Engine / PulleysEngine Model Frame Steer Cable Bracket RH Wheel Assembly LHWheels Steer Cable Bracket LH Axle Lobe CoverWheel Lobe Spring Retainer PIN Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY BAG of Parts Decals 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Warranty Statement

REPAIR PARTS

HANDLES

KEY

KNOB BLACK

WASHER 3/8