532 42 13-51 Console Panel Gray, Bulb

REPAIR PARTS

HANDLES

SNOWTHROWER-MODELNO.1330SB-XLSB(96193004100),PRODUCTNO.9619300-41

			KEY	PART	DESCRIPTION
			NO.	NO.	DESCRIPTION
		3	1	532 41 62-88 INTERLOCK SPRING
	2		2	532 41 45-72 INTERLOCK CAM
5	2		3	532 17 88-31 TORSION SPRING
			4	532 16 96-75	RETAINER
			5	817 06 04-10 SCREW 1/4−20 X .625
	1		6	532 42 18-14 INTERLOCK STOP
	1
	6	01.08.007-B

7 5

1	6
1
	4
	5	KEY	PART	DESCRIPTION
		NO.	NO.	DESCRIPTION
		1	532 42 13-51 CONSOLE PANEL GRAY
		2	532 42 14-48 HEADLIGHT BEZEL GRAY
		3	532 17 86-66 HALOGEN HEADLIGHT
	4	4	532 18 44-71	SHOULDER SCREW 10−24 X .625
	4	5	532 17 52-62 SCREW 10−24 X 1.25
		5	532 17 52-62 SCREW 10−24 X 1.25
		6	532 41 77-60	GRIP SWITCH
		7	532 40 56-99 WIRE HARNESS
		8	532 40 16-20	BULB

01.10.010-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 30

Page 30

Image 30

Husqvarna 1330SB-XLSB 532 42 13-51 Console Panel Gray, 532 42 14-48 Headlight Bezel Gray, 532 17 86-66 Halogen Headlight

Contents

1330SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents EXT RA Shear Bolts and Nuts Chute Deflector Remote ControlParts Packed Separately in Carton Rotator Head Mounting Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower Stopping To Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See Fig To USE Drift Cutters See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Snow ThrowerEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Storage Other Troubleshooting Repair Parts Auger Housing / Impeller Assembly KEY Part Description Auger Assembly 30 LH Auger Assembly 30 RH Auger Ball Bearing Skid Plate Weight BAR CARRIAGEBOLT5/16−18X.750 POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer Strap Rotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot Bracket Handles POP Rivet 1/8 01.12.002-C 532 42 14-48 Headlight Bezel Gray Grip Switch532 42 13-51 Console Panel Gray 532 17 86-66 Halogen Headlight Thrust Washer DriveAxle Shaft Clik PIN 921 01.02.002-F Idler Pulley 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Clevis PIN 01.01.001-B Frame Chassis / Engine / PulleysEngine Model Bottom PAN Steer Cable Bracket LH Wheel Assembly LHWheels Steer Cable Bracket RH Spring CoverWheel Lobe Axle Lobe BAG of Parts Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY Retainer PIN Decals 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Warranty Statement

Husqvarna 1330SB-XLSB 532 42 13-51 Console Panel Gray, 532 42 14-48 Headlight Bezel Gray, Bulb

Models: 1330SB-XLSB

REPAIR PARTS

HANDLES

KEY

KEY

532 42 13-51 CONSOLE PANEL GRAY

532 42 14-48 HEADLIGHT BEZEL GRAY

532 17 86-66 HALOGEN HEADLIGHT

GRIP SWITCH

BULB