Rotator Head, Rotator Pivot Bracket | Husqvarna 1330SB-XLSB instruction

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOWTHROWER-MODELNO.1330SB-XLSB(96193004100),PRODUCTNO.9619300-41

	1
*3	*6
	*6

KEY	PART		*4
NO.	NO.	DESCRIPTION		01.09.008-B	*5

1532 42 11-60 LEVER/CABLE ROTATOR ASSEMBLY GRAY

2817 50 10-10 SCREW 10−24 X .625

*3	532 42 06-78	ROTATOR HEAD
*4	532 42 11-61	ROTATOR PIVOT BRACKET
*5	532 42 06-75	PULLEY PIVOT
*6	532 42 11-62	CABLE ASSEMBLY GRAY

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

1 01.15.008-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 42 12-31	STEER CABLE
2	874 04 10-24	SCREW 10−24 X 1.50

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 26

Page 26

Image 26

Husqvarna 1330SB-XLSB 532 42 11-60 LEVER/CABLE Rotator Assembly Gray, Rotator Head, Rotator Pivot Bracket, Pulley Pivot

Contents

1330SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents EXT RA Shear Bolts and Nuts Chute Deflector Remote ControlParts Packed Separately in Carton Rotator Head Mounting Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Check Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower Stopping To Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See Fig To USE Drift Cutters See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Engine CleaningSnow Thrower Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Storage Other Troubleshooting Repair Parts Auger Housing / Impeller Assembly KEY Part Description Auger Assembly 30 LH Auger Assembly 30 RH Auger Ball Bearing Skid Plate Weight BAR CARRIAGEBOLT5/16−18X.750 POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer Strap Rotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot Bracket Handles POP Rivet 1/8 01.12.002-C 532 42 14-48 Headlight Bezel Gray Grip Switch532 42 13-51 Console Panel Gray 532 17 86-66 Halogen Headlight Thrust Washer DriveAxle Shaft Clik PIN 921 01.02.002-F Idler Pulley 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Clevis PIN 01.01.001-B Frame Chassis / Engine / PulleysEngine Model Bottom PAN Steer Cable Bracket LH Wheel Assembly LHWheels Steer Cable Bracket RH Spring CoverWheel Lobe Axle Lobe BAG of Parts Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY Retainer PIN 532 18 37-30 DECAL, Remote Deflector Decals532 18 10-35 DECAL, DANGER, Deflector Warranty Statement

Husqvarna 1330SB-XLSB 532 42 11-60 LEVER/CABLE Rotator Assembly Gray, Rotator Head, Pulley Pivot

Models: 1330SB-XLSB

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

KEY

1532 42 11-60 LEVER/CABLE ROTATOR ASSEMBLY GRAY

ROTATOR HEAD

ROTATOR PIVOT BRACKET

PULLEY PIVOT

CABLE ASSEMBLY GRAY

KEY

STEER CABLE