Repair Parts, 532 18 41-13 Deflector Weldment

	REPAIR PARTS	CONTROL PANEL / DISCHARGE CHUTE
	SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44
	2
		11
		10
		5
		8
	3	6
		6
		9
		11
	6	4
	6	11
		11

	7
1	KEY	PART
	NO.	NO.	DESCRIPTION
	1	532 40 76-50 CHUTE WELDMENT
	2	532 18 41-13 DEFLECTOR WELDMENT
	3	532 42 03-25 DEFLECTOR SEAL
	4	532 18 41-14	STRAP
	5	532 19 19-38	KNOB BLACK
	6	532 12 84-15	POP RIVET
	7	532 18 56-00 SHOULDER BOLT 1/4−20 X .704
	8	872 27 05-05 CARRIAGE BOLT 5/16−18 X .625
	9	532 19 17-30	NUT 1/4−20
01.09.001-A	10	532 15 54-15	WASHER
	11	532 17 92-46 PLASTIC WASHER

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 24

Image 24

Husqvarna 927SB, 96193004400 owner manual Repair Parts, 532 18 41-13 Deflector Weldment, Strap, Knob Black, POP Rivet

Contents

927SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Operation Know Your Snow ThrowerPrimer Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for startingDrive speed control lever used to select forward or HOW to USE Your Snow Thrower Stopping When traction drive control lever is engaged Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Throw Snow See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See Fig Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has Frozen Maintenance Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig Storage CarburetorEngine Speed Fuel System Other Cylinder Troubleshooting Auger Housing / Impeller Assembly KEY Part DescriptionScraper BAR Auger Bearing Auger 27 LH Auger 27 RH Exploded 532 19 67-10 Gearbox Assembly ImpellerBearing Tool Clip Repair Parts 532 18 41-13 Deflector WeldmentStrap Knob Black Control Panel / Discharge Chute Handles 532 42 14-48 Headlight Bezel GrayBulb Lower Tube 01.08.004-B Spacer RetainerKnob RED Handle Knob 532 18 04-80 Impeller ROD Assembly 532 40 57-40 Traction ROD AssemblyClutch ROD Rear Plate Drive 532 17 53-44 Trunnion Bearing Assembly Control Shaft AssemblyHEX Shaft Pinion Gear 3534 Assembly 532 18 40-74 Idler Pivot Bracket Assembly 532 17 93-54 Idler Traction ARM532 19 84-74 Speed Selector Head Idler Pulley Axle Shaft Roll PIN 3/16Gear Clik PIN ENGINE, TEC FrameBottom PAN Chassis / Engine / Pulleys PulleyImpeller Belt Wheel Assembly LH Wheels Power Cord KEY Part Description 532 03 50-62 Safety Ignition KEYBAG of Parts Retainer PIN Decals 532 18 10-35 DECAL, DANGER, Deflector Warranty Statement

Husqvarna 927SB Repair Parts, 532 18 41-13 Deflector Weldment, Strap, Knob Black, POP Rivet

Models: 96193004400 927SB

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44

KEY

532 18 41-13 DEFLECTOR WELDMENT

STRAP

KNOB BLACK

POP RIVET

WASHER