532 18 04-80 Impeller ROD Assembly | Husqvarna 96193004400, 927SB

REPAIR PARTS

HANDLES

SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44

10			KEY	PART
	2		NO.	NO.	DESCRIPTION
			1	532 18 04-80 IMPELLER ROD ASSEMBLY
			2	532 40 57-40 TRACTION ROD ASSEMBLY
			3	532 18 04-45 SHIFTER ROD TOP
10			4	532 18 77-16 SHIFTER ROD BOTTOM
10			5	532 18 04-47 SPRING SLEEVE
			5	532 18 04-47 SPRING SLEEVE
			6	532 17 86-69 IMPELLER SPRING
1			7	532 18 09-26 TRACTION SPRING
1			8	872 27 05-06	CARRIAGE BOLT 5/16−18 X .750
			8	872 27 05-06	CARRIAGE BOLT 5/16−18 X .750
			9	532 15 53-77	NUT 5/16−18
			10	532 16 96-75	RETAINER
			11	532 40 33-00	CLUTCH ROD
			12	532 41 69-21	REAR PLATE
	3		13	532 41 54-33 SHIFTER PLATE BRACKET
	3		14	532 41 68-64 CLUTCH PLATE BRACKET
			15	532 41 54-35 CLUTCH PLATE
9			16	532 41 54-50 SHIFTER PLATE
	8		17	532 15 00-78 BOLT 5/16−18 X .750
	5		18	532 40 28-81	SHOULDER BOLT 1/4−20 X .500
	5		19	532 19 17-30	NUT 1/4−20
			19	532 19 17-30	NUT 1/4−20
	4
		7
			18
5	18	17	19
	18	19	19
	18	19
	18		15
			15
			14
	10
6	16
	17			11
	13 19			11
	13 19
	01.12.006-C		12
	01.12.006-C

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

29

Image 29

Husqvarna 96193004400 532 18 04-80 Impeller ROD Assembly, 532 40 57-40 Traction ROD Assembly, Clutch ROD, Rear Plate

Contents

927SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See Figs Know Your Snow Thrower OperationPrimer Ignition KEY Drive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting Stopping HOW to USE Your Snow Thrower Using the CLEAN-OUT Tool See Fig When traction drive control lever is engagedTo Move Forward and Backward See Fig To Throw Snow See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen Maintenance Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig Carburetor StorageEngine Speed Fuel System Cylinder Other Troubleshooting KEY Part Description Auger Housing / Impeller AssemblyScraper BAR Auger Bearing Auger 27 RH Auger 27 LH Exploded Impeller 532 19 67-10 Gearbox AssemblyBearing Tool Clip 532 18 41-13 Deflector Weldment Repair PartsStrap Knob Black Control Panel / Discharge Chute 532 42 14-48 Headlight Bezel Gray HandlesBulb Lower Tube 01.08.004-B Retainer SpacerKnob RED Handle Knob 532 40 57-40 Traction ROD Assembly 532 18 04-80 Impeller ROD AssemblyClutch ROD Rear Plate Drive Control Shaft Assembly 532 17 53-44 Trunnion Bearing AssemblyHEX Shaft Pinion Gear 3534 Assembly 532 17 93-54 Idler Traction ARM Assembly 532 18 40-74 Idler Pivot Bracket532 19 84-74 Speed Selector Head Idler Pulley Roll PIN 3/16 Axle ShaftGear Clik PIN Bottom PAN ENGINE, TECFrame Impeller Belt Chassis / Engine / PulleysPulley Wheels Wheel Assembly LH KEY Part Description 532 03 50-62 Safety Ignition KEY Power CordBAG of Parts Retainer PIN 532 18 10-35 DECAL, DANGER, Deflector Decals Warranty Statement