Auger Housing / Impeller Assembly, Scraper BAR

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44

3 (5x)

4 (5x)

01.07.002-A

KEY	PART
NO.	NO.	DESCRIPTION
1	532 40 77-99 AUGER HOUSING 27
2	532 40 77-27	SCRAPER BAR
3	872 27 05-05 CARRIAGE BOLT 5/16−18 X .625
4	532 15 53-77	NUT 5/16−18

2	3

		KEY	PART
		NO.	NO.		DESCRIPTION
		1	532	42 04-78	AUGER BEARING
3		2	532	41 19-39	BEARING PLUG
	01.07.024-B	3	532	17 95-82	SCREW 5/16−18 X 1.00
	01.07.024-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 20

Page 20

Image 20

Husqvarna 927SB Auger Housing / Impeller Assembly, KEY Part Description, Scraper BAR, Auger Bearing, Bearing Plug

Contents

927SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Operation Know Your Snow ThrowerPrimer Ignition KEY Drive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting HOW to USE Your Snow Thrower Stopping When traction drive control lever is engaged Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Throw Snow See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See Fig Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has Frozen Maintenance Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig Storage CarburetorEngine Speed Fuel System Other Cylinder Troubleshooting Auger Housing / Impeller Assembly KEY Part DescriptionScraper BAR Auger Bearing Auger 27 LH Auger 27 RH Exploded 532 19 67-10 Gearbox Assembly ImpellerBearing Tool Clip Repair Parts 532 18 41-13 Deflector WeldmentStrap Knob Black Control Panel / Discharge Chute Handles 532 42 14-48 Headlight Bezel GrayBulb Lower Tube 01.08.004-B Spacer RetainerKnob RED Handle Knob 532 18 04-80 Impeller ROD Assembly 532 40 57-40 Traction ROD AssemblyClutch ROD Rear Plate Drive 532 17 53-44 Trunnion Bearing Assembly Control Shaft AssemblyHEX Shaft Pinion Gear 3534 Assembly 532 18 40-74 Idler Pivot Bracket Assembly 532 17 93-54 Idler Traction ARM532 19 84-74 Speed Selector Head Idler Pulley Axle Shaft Roll PIN 3/16Gear Clik PIN Bottom PAN ENGINE, TECFrame Impeller Belt Chassis / Engine / PulleysPulley Wheel Assembly LH Wheels Power Cord KEY Part Description 532 03 50-62 Safety Ignition KEYBAG of Parts Retainer PIN Decals 532 18 10-35 DECAL, DANGER, Deflector Warranty Statement

Husqvarna 927SB, 96193004400 Auger Housing / Impeller Assembly, KEY Part Description, Scraper BAR

Models: 96193004400 927SB

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44

KEY

PART

DESCRIPTION

SCRAPER BAR

AUGER BEARING

BEARING PLUG