Manuals / Husqvarna / Lawn and Garden / Snow Blower

Husqvarna 96193004400, 927SB Repair Parts, Drive, Description, 817 49 05-08BOLT 5/16−18

Models: 96193004400 927SB

1 40

Download 40 pages 15.34 Kb

Page 31

REPAIR PARTS

DRIVE

SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44

KEY	PART
NO.	NO.	DESCRIPTION
1	817 49 05-08 BOLT 5/16−18 X .500
2	532 75 11-53	NUT 5/16−18
3	532 18 00-17 FLANGE BEARING
4	873 93 05-00	NUT 5/16−18

5532 19 95-09 RUBBER WHEEL PLATE

6532 17 98-31 RUBBER WHEEL RING

7532 17 86-13 RUBBER WHEEL HUB

8874 76 05-14 BOLT 5/16−18 X .875

9532 17 53-44 TRUNNION BEARING ASSEMBLY

10	812 00 00-12	RETAINER
11	532 18 00-66	HEX SHAFT
12	532 18 00-65	PINION GEAR

13532 19 29-07 AUXILIARY PLATE

14532 17 92-70 SPACER PLATE

15532 18 00-82 INTERMEDIATE GEAR

16532 18 01-34 AUXILIARY SHAFT

17532 40 54-85 CONTROL ARM

18	532 05 70-79	WASHER
19	532 40 61-09	CONTROL SHAFT ASSEMBLY
20	532 19 85-80	CLEVIS PIN

21532 18 40-80 SHIFTER LEVER

22532 18 78-57 PIVOT BRACKET

23	532 17 88-07	PIVOT PIN
24	532 18 01-35	SPRING
25	532 18 71-01	SHIFTER LINK
26	532 08 51-79	RETAINER
27	532 70 02-79	CLIP
28	532 15 00-78 BOLT 5/16−18 x .750

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 31

Image 31

Husqvarna 96193004400, 927SB owner manual Repair Parts, Drive, Description, 817 49 05-08BOLT 5/16−18

Contents

927SB Preparation TrainingOperation CUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS Maintenance and StorageREMOVE SNOW THROWER FROM CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER PARTS PACKED SEPARATELY IN CARTONINSTALL SPEED CONTROL ROD See Figs. 1 and ASSEMBLY / PRE-OPERATIONUNFOLD UPPER HANDLE INSTALL AUGER CONTROL ROD See Figs. 5 and ASSEMBLY / PRE-OPERATIONKNOW YOUR SNOW THROWER OPERATIONOPERATION MEETS A.N.S.I. SAFETY REQUIREMENTSSTOPPING HOW TO USE YOUR SNOW THROWEROPERATION TO USE CHOKE CONTROL See FigTO MOVE FORWARD AND BACKWARD See Fig when traction drive control lever is engagedUSING THE CLEAN-OUTTOOL See Fig OPERATIONSCRAPER BAR See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig OPERATIONBEFORE STOPPING SNOW THROWING TIPSOPERATION TO START ENGINEBEFORE EACH USE MAINTENANCELUBRICATION CHART GENERAL RECOMMENDATIONSAUGER GEAR CASE CLEANINGENGINE MAINTENANCESNOW THROWER SERVICE AND ADJUSTMENTS2.Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig SERVICE AND ADJUSTMENTSSNOW THROWER STORAGESERVICE AND ADJUSTMENTS ENGINESTORAGE OTHERCYLINDER Engine idles or TROUBLESHOOTINGLoss of power Does not startDESCRIPTION REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY PARTDESCRIPTION REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY PART7 8 17 26 REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY 9 2DESCRIPTION REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY PARTDESCRIPTION REPAIR PARTSCONTROL PANEL / DISCHARGE CHUTE PARTDESCRIPTION CONTROL PANEL / DISCHARGE CHUTEREPAIR PARTS PARTDESCRIPTION HANDLESREPAIR PARTS PARTPART 4 3 3 2 01.08.004-BREPAIR PARTS HANDLESHANDLES REPAIR PARTS12 14 14 01.08.002-E PART REPAIR PARTS532 18 04-80IMPELLER ROD ASSEMBLY HANDLESREPAIR PARTS DRIVEDESCRIPTION REPAIR PARTSDRIVE PARTDRIVE REPAIR PARTS01.02.001-G Sheet PART REPAIR PARTSDRIVE PARTDESCRIPTION REPAIR PARTSDRIVE PARTPART REPAIR PARTSCHASSIS / ENGINE / PULLEYSDESCRIPTION DESCRIPTION CHASSIS / ENGINE / PULLEYSREPAIR PARTS PARTDESCRIPTION WHEELSREPAIR PARTS PARTPART BAG OF PARTSREPAIR PARTS 532 03 50-62SAFETY IGNITION KEYDESCRIPTION DECALSREPAIR PARTS PARTSECTION 4 EXCEPTIONS AND LIMITATIONS WARRANTY STATEMENTSECTION 1 LIMITED WARRANTY SECTION 3 ITEMS NOT COVERED BY THIS WARRANTY