Manuals / Husqvarna / Lawn and Garden / Snow Blower

Husqvarna 927SB, 96193004400 owner manual Repair Parts, Drive, Description, 532

Models: 96193004400 927SB

1 40

Download 40 pages 15.34 Kb

Page 34

Image 34

REPAIR PARTS

DRIVE

SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44

	6
1b	4
7	3
	3
1b
6	1a

			KEY	PART
		2	NO.	NO.	DESCRIPTION
		3	1	532 18 82-26	(assy of 1a,1b) AXLE ASSEMBLY
		3	1a	532 17 93-52	AXLE SHAFT
5	4		1a	532 17 93-52	AXLE SHAFT
5	4	01.03.004-B	1b	532 18 42-06	ROLL PIN 3/16
		01.03.004-B	2	532 18 00-81	GEAR
			2	532 18 00-81	GEAR
			3	532 17 46-97 THRUST WASHER
			4	532 17 98-30	BEARING
			5	817 49 05-08 BOLT 5/16-18 X .500
			6	532 15 54-43	CLIK PIN
			7	532 18 92-82	SQUARE KEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 34

Page 34

Image 34

Husqvarna 927SB, 96193004400 owner manual Repair Parts, Drive, Description, 532

Contents

927SB Preparation TrainingOperation Maintenance and Storage TABLE OF CONTENTSPRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIESPARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONINSTALL SPEED CONTROL ROD See Figs. 1 and ASSEMBLY / PRE-OPERATIONUNFOLD UPPER HANDLE ASSEMBLY / PRE-OPERATION INSTALL AUGER CONTROL ROD See Figs. 5 andOPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS OPERATIONTO USE CHOKE CONTROL See Fig HOW TO USE YOUR SNOW THROWEROPERATION STOPPINGOPERATION when traction drive control lever is engagedUSING THE CLEAN-OUTTOOL See Fig TO MOVE FORWARD AND BACKWARD See FigOPERATION BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig SCRAPER BAR See FigTO START ENGINE SNOW THROWING TIPSOPERATION BEFORE STOPPINGGENERAL RECOMMENDATIONS MAINTENANCELUBRICATION CHART BEFORE EACH USEMAINTENANCE CLEANINGENGINE AUGER GEAR CASETO ADJUST SNOW THROWER HEIGHT SERVICE AND ADJUSTMENTS2.Remove safety ignition key SNOW THROWERSERVICE AND ADJUSTMENTS TO REPLACE BELTS See FigENGINE STORAGESERVICE AND ADJUSTMENTS SNOW THROWERSTORAGE OTHERCYLINDER Does not start TROUBLESHOOTINGLoss of power Engine idles orPART REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTIONPART REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTION9 2 REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY 7 8 17 26PART REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTIONPART REPAIR PARTSCONTROL PANEL / DISCHARGE CHUTE DESCRIPTIONPART CONTROL PANEL / DISCHARGE CHUTEREPAIR PARTS DESCRIPTIONPART HANDLESREPAIR PARTS DESCRIPTIONHANDLES 4 3 3 2 01.08.004-BREPAIR PARTS PARTHANDLES REPAIR PARTS12 14 14 01.08.002-E HANDLES REPAIR PARTS532 18 04-80IMPELLER ROD ASSEMBLY PARTDRIVE REPAIR PARTSPART REPAIR PARTSDRIVE DESCRIPTIONDRIVE REPAIR PARTS01.02.001-G Sheet PART REPAIR PARTSDRIVE PARTPART REPAIR PARTSDRIVE DESCRIPTIONPART REPAIR PARTSCHASSIS / ENGINE / PULLEYSDESCRIPTION PART CHASSIS / ENGINE / PULLEYSREPAIR PARTS DESCRIPTIONPART WHEELSREPAIR PARTS DESCRIPTION532 03 50-62SAFETY IGNITION KEY BAG OF PARTSREPAIR PARTS PARTPART DECALSREPAIR PARTS DESCRIPTIONSECTION 3 ITEMS NOT COVERED BY THIS WARRANTY WARRANTY STATEMENTSECTION 1 LIMITED WARRANTY SECTION 4 EXCEPTIONS AND LIMITATIONS