Drive

REPAIR PARTS

SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44

		24
		23							1	2
	27		21						3
			21					28	1	1
								28	1
	25
	25	27		28			2
							2
						14
										16


		22						142	1
			2					142	3
		26	2	2				13	15
			1					13
	28
		28
		28	2						2
			2					14	2
								14
						3	2		20
			12		1	3	2
					1

							17	18
		11					17
	8	11
8	8								19
									19
		10
		10
		9

				8
	4			7
	4			5
1	4			5
1				6
				6
			5	01.02.001-F_Sheet_1
2		3	4
2
	1

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 30

Image 30

Husqvarna 927SB, 96193004400 owner manual Drive

Contents

927SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for startingDrive speed control lever used to select forward or HOW to USE Your Snow Thrower Stopping To Move Forward and Backward See Fig When traction drive control lever is engagedUsing the CLEAN-OUT Tool See Fig To Throw Snow See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Maintenance Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Engine Speed StorageCarburetor Fuel System Other Cylinder Troubleshooting Scraper BAR Auger Housing / Impeller AssemblyKEY Part Description Auger Bearing Auger 27 LH Auger 27 RH Exploded Bearing 532 19 67-10 Gearbox AssemblyImpeller Tool Clip Strap Repair Parts532 18 41-13 Deflector Weldment Knob Black Control Panel / Discharge Chute Bulb Handles532 42 14-48 Headlight Bezel Gray Lower Tube 01.08.004-B Knob RED SpacerRetainer Handle Knob Clutch ROD 532 18 04-80 Impeller ROD Assembly532 40 57-40 Traction ROD Assembly Rear Plate Drive HEX Shaft 532 17 53-44 Trunnion Bearing AssemblyControl Shaft Assembly Pinion Gear 3534 532 19 84-74 Speed Selector Head Assembly 532 18 40-74 Idler Pivot BracketAssembly 532 17 93-54 Idler Traction ARM Idler Pulley Gear Axle ShaftRoll PIN 3/16 Clik PIN ENGINE, TEC FrameBottom PAN Chassis / Engine / Pulleys PulleyImpeller Belt Wheel Assembly LH Wheels BAG of Parts Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY Retainer PIN Decals 532 18 10-35 DECAL, DANGER, Deflector Warranty Statement

		24
		23							1	2
	27		21						3
			21					28	1	1
								28	1
	25
	25	27		28			2
							2
						14
										16


		22						142	1
			2					142	3
		26	2	2				13	15
			1					13
	28
		28
		28	2						2
			2					14	2
								14
						3	2		20
			12		1	3	2
					1

							17	18
		11					17
	8	11
8	8								19
									19
		10
		10
		9

		24
		23							1	2
	27		21						3
			21					28	1	1
								28	1
	25
	25	27		28			2
							2
						14
										16


		22						142	1
			2					142	3
		26	2	2				13	15
			1					13
	28
		28
		28	2						2
			2					14	2
								14
						3	2		20
			12		1	3	2
					1

							17	18
		11					17
	8	11
8	8								19
									19
		10
		10
		9

		24
		23							1	2
	27		21						3
			21					28	1	1
								28	1
	25
	25	27		28			2
							2
						14
										16


		22						142	1
			2					142	3
		26	2	2				13	15
			1					13
	28
		28
		28	2						2
			2					14	2
								14
						3	2		20
			12		1	3	2
					1

							17	18
		11					17
	8	11
8	8								19
									19
		10
		10
		9