Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna MZ6125BF / 968999721 operation, Set the choke control, Fuel valve in the OPEN position

Models: MZ6125, MZ7227, MZ5225BF, MZ6125BF, MZ5225C, MZ6125C, MZ25, MZ5225 MZ5225 / 968999717 MZ25 / 968999780 MZ5225C / 968999748 MZ6125 / 968999718 MZ5225BF / 968999720 MZ7227 / 968999719 MZ6125BF / 968999721 MZ6125C / 968999749

1 77

Download 77 pages 13.21 Kb

Page 28

Image 28

operation

If the engine is cold, the choke control should be pulled out to its extent.

Open the fuel valve.

Press in and turn the ignition key to the start position

8061-004

Set the choke control

8011-438

Fuel valve in the OPEN position

8061-011

Turn to START position

English-28

Page 28

Image 28

Husqvarna MZ6125BF / 968999721 operation, Set the choke control, Fuel valve in the OPEN position, Turn to START position

Contents

English Operators ManualMZ5225 MZ6125Page Contents Driving and Transport on Public RoadsPage INTRODUCTION CongratulationsGeneral Driving and Transport on Public RoadsGood Service Manufacturing NumberPlease have these available when ordering spare parts INTRODUCTIONsymbols and decals Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxxIMPORTANT INFORMATION xxxxxxsymbols and decals remove safetyremove key before Moving sharp blades under coverSafety Instructions SAFETYGeneral Operation SAFETY Operate machine only in daylight or good artificial lightSlope Operation Personal Safety EquipmentSAFETY Children SAFETYSafe Handling of Gasoline The engine and the exhaust system become very hot during operationThere is risk for burns if touched SAFETYUse protective glasses for maintenance work General MaintenanceSAFETY Risk of sparking SAFETYEnglish-15 IMPORTANT INFORMATION TransportSAFETY Roll over Protection system ROPS SAFETYCONTROLS Control LocationsCONTROLS 1. Steering Control Levers1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse 4. Blade Switch 2. Parking Brake3. Throttle Control CONTROLS5. Ignition Switch 6. Choke Control7. Fuses CONTROLS8. Fuel Tank The engine and the exhaust system, become very hot during operationRisk for burns if touched CONTROLS9. Fuel Shut Off Valve 10. Lifting Lever for the Mower DeckIMPORTANT INFORMATION Always use the high position to transport CONTROLS11. Seat Adjustment Lever 12. Hour Meter13. Tracking Knob CONTROLSoperation TrainingSteering To move forward and backwardStarting the Engine Before Startingoperation operation Press the control for disengaging the mower deckPlace controls in neutral position Set the throttleoperation Set the choke controlFuel valve in the OPEN position Turn to START positionoperation IMPORTANT INFORMATIONRelease ignition to the RUN position Set the engine speedStarting the engine with a weak battery To attach jumper cablesTo remove cables, reverse order operationRunning Ensure that no one is near mower when engaging blade switchoperation operation Operating on hillsIMPORTANT INFORMATION Mowing Tips operationStopping the Engine operationoperation Pump release valvesIMPORTANT INFORMATION Tighten the valve moderately MAINTENANCE Maintenance ScheduleMAINTENANCE English-37Battery Always use protective glasses when handling the batteryTo clean battery and terminals Replacing batterySafety System Ignition SystemFitting the wrong spark plug type can damage the engine MAINTENANCEEngine Cooling Air Intake Throttle CableChoke Cable MAINTENANCEAir Filter Maintenance Do not use compressed air to clean the air filterDo not tap filter to clean this could cause damage to the sealing Servicing PrecleanerReplacing the Fuel Filter Fuel Pump Air FilterTire Pressures MAINTENANCEParking Brake V-beltsMAINTENANCE IMPORTANT INFORMATIONDeck belt installation Deck beltDeck belt removal MAINTENANCEBelt installation Pump BeltCutting Blades Replacing pump beltIMPORTANT INFORMATION Special blade bolt is heat treated Replace with a Husqvarna bolt if requiredDo not use lower grade hardware than specified MAINTENANCEAdjusting the Mower Deck Before performing any service or adjustment checklist2. Place the Blade switch in the disengaged position 3. Turn ignition switch to “OFF” position and remove the keyAdjust anti-scalp rollers with the mower on a flat level surface Anti-scalp rollersMAINTENANCE IMPORTANT INFORMATIONCleaning and Washing Use protective glasses when cleaning and washingRemoval and installation of caster wheel Caster WheelsGeneral Change transaxles transmission filtersLUBRICATION LUBRICATION Lubricating the Cables1. Front Wheel Mount 2. Front Wheel BearingsEngine Oil Avoid skin contact wash with soap and water in case of spills4. Engine Oil Filter 5. Changing the Engine OilNever fill to above the “FULL” mark Engine Oil LevelsLUBRICATION Purging Procedures Hydraulic PumpFluid Change LUBRICATIONProblem TROUBLESHOOTINGCause TROUBLESHOOTING ProblemCause English-56Service STORAGEStorage Winter Storageschematics TECHNICAL DATA MZ5225MZ6125 MZ5225BFOverall Dimensions ProductivityTECHNICAL DATA MZ5225MZ7227 MZ25TECHNICAL DATA EngineTECHNICAL DATA Overall DimensionsMZ7227 MZ25Torque Specifications AccessoriesTECHNICAL DATA TORQUE SPECIFICATIONS HEX HEAD CAP SCREWS U.S. Standard HardwareMetric Standard Hardware TECHNICAL DATAUSA requirements CONForMITY CERTIFICATESCE requirements SERVICE JOURNAL Delivery ServiceAction Date, mtr reading, stamp, signAfter the First 5-8 Hours SERVICE JOURNALAction Date, mtr reading, stamp, sign25-Hour Service SERVICE JOURNAL3. Check the tire pressures 4. Check battery with cables 5. Lubricate according to lubrication chart50-Hour Service SERVICE JOURNAL1. Perform the 25-hour service 2. Clean/replace the air cleaner’s filter cartridge paper filter100-Hour Service SERVICE JOURNAL1. Perform the 25-hour service 2. Perform the 50-hour service 3. Change the engine oil filter 4. Clean/replace the spark plugs300-Hour Service SERVICE JOURNALAction Date, mtr reading, stamp, signAt Least Once Each Year SERVICE JOURNALAction Date, mtr reading, stamp, signSERVICE JOURNAL ActionDate, mtr reading, stamp, sign English-73SERVICE JOURNAL ActionDate, mtr reading, stamp, sign English-74Page WARRANTY STATEMENT SECTION 1 LIMITED WARRANTYSECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY SECTION 6 PROCEDURE TO OBTAIN WARRANTY CONSIDERATIONP/N 539 132401 R01 03/27/08