MZ6125
English
Operators Manual
MZ5225
Page
Driving and Transport on Public Roads
Contents
Page
Driving and Transport on Public Roads
INTRODUCTION
Congratulations
General
INTRODUCTION
Good Service
Manufacturing Number
Please have these available when ordering spare parts
xxxxxx
symbols and decals
Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx
IMPORTANT INFORMATION
Moving sharp blades under cover
symbols and decals
remove safety
remove key before
Safety Instructions
SAFETY
General Operation
Operate machine only in daylight or good artificial light
SAFETY
Slope Operation
Personal Safety Equipment
SAFETY
SAFETY
Children
SAFETY
Safe Handling of Gasoline
The engine and the exhaust system become very hot during operation
There is risk for burns if touched
Use protective glasses for maintenance work
General Maintenance
SAFETY
Risk of sparking
SAFETY
English-15
IMPORTANT INFORMATION
Transport
SAFETY
SAFETY
Roll over Protection system ROPS
Control Locations
CONTROLS
CONTROLS
1. Steering Control Levers
1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse
CONTROLS
4. Blade Switch
2. Parking Brake
3. Throttle Control
CONTROLS
5. Ignition Switch
6. Choke Control
7. Fuses
CONTROLS
8. Fuel Tank
The engine and the exhaust system, become very hot during operation
Risk for burns if touched
CONTROLS
9. Fuel Shut Off Valve
10. Lifting Lever for the Mower Deck
IMPORTANT INFORMATION Always use the high position to transport
CONTROLS
11. Seat Adjustment Lever
12. Hour Meter
13. Tracking Knob
To move forward and backward
operation
Training
Steering
Starting the Engine
Before Starting
operation
Set the throttle
operation
Press the control for disengaging the mower deck
Place controls in neutral position
Turn to START position
operation
Set the choke control
Fuel valve in the OPEN position
Set the engine speed
operation
IMPORTANT INFORMATION
Release ignition to the RUN position
operation
Starting the engine with a weak battery
To attach jumper cables
To remove cables, reverse order
Running
Ensure that no one is near mower when engaging blade switch
operation
operation
Operating on hills
IMPORTANT INFORMATION
operation
Mowing Tips
operation
Stopping the Engine
operation
Pump release valves
IMPORTANT INFORMATION Tighten the valve moderately
Maintenance Schedule
MAINTENANCE
English-37
MAINTENANCE
Replacing battery
Battery
Always use protective glasses when handling the battery
To clean battery and terminals
MAINTENANCE
Safety System
Ignition System
Fitting the wrong spark plug type can damage the engine
MAINTENANCE
Engine Cooling Air Intake
Throttle Cable
Choke Cable
Servicing Precleaner
Air Filter Maintenance
Do not use compressed air to clean the air filter
Do not tap filter to clean this could cause damage to the sealing
MAINTENANCE
Replacing the Fuel Filter
Fuel Pump Air Filter
Tire Pressures
IMPORTANT INFORMATION
Parking Brake
V-belts
MAINTENANCE
MAINTENANCE
Deck belt installation
Deck belt
Deck belt removal
Replacing pump belt
Belt installation
Pump Belt
Cutting Blades
MAINTENANCE
IMPORTANT INFORMATION Special blade bolt is heat treated
Replace with a Husqvarna bolt if required
Do not use lower grade hardware than specified
3. Turn ignition switch to “OFF” position and remove the key
Adjusting the Mower Deck
Before performing any service or adjustment checklist
2. Place the Blade switch in the disengaged position
IMPORTANT INFORMATION
Adjust anti-scalp rollers with the mower on a flat level surface
Anti-scalp rollers
MAINTENANCE
Caster Wheels
Cleaning and Washing
Use protective glasses when cleaning and washing
Removal and installation of caster wheel
General
Change transaxles transmission filters
LUBRICATION
2. Front Wheel Bearings
LUBRICATION
Lubricating the Cables
1. Front Wheel Mount
5. Changing the Engine Oil
Engine Oil
Avoid skin contact wash with soap and water in case of spills
4. Engine Oil Filter
Never fill to above the “FULL” mark
Engine Oil Levels
LUBRICATION
LUBRICATION
Purging Procedures
Hydraulic Pump
Fluid Change
Problem
TROUBLESHOOTING
Cause
English-56
TROUBLESHOOTING
Problem
Cause
Winter Storage
Service
STORAGE
Storage
schematics
MZ5225BF
TECHNICAL DATA
MZ5225
MZ6125
MZ5225
Overall Dimensions
Productivity
TECHNICAL DATA
Engine
MZ7227
MZ25
TECHNICAL DATA
MZ25
TECHNICAL DATA
Overall Dimensions
MZ7227
Torque Specifications
Accessories
TECHNICAL DATA
TECHNICAL DATA
TORQUE SPECIFICATIONS HEX HEAD CAP SCREWS
U.S. Standard Hardware
Metric Standard Hardware
USA requirements
CONForMITY CERTIFICATES
CE requirements
Date, mtr reading, stamp, sign
SERVICE JOURNAL
Delivery Service
Action
Date, mtr reading, stamp, sign
After the First 5-8 Hours
SERVICE JOURNAL
Action
5. Lubricate according to lubrication chart
25-Hour Service
SERVICE JOURNAL
3. Check the tire pressures 4. Check battery with cables
2. Clean/replace the air cleaner’s filter cartridge paper filter
50-Hour Service
SERVICE JOURNAL
1. Perform the 25-hour service
3. Change the engine oil filter 4. Clean/replace the spark plugs
100-Hour Service
SERVICE JOURNAL
1. Perform the 25-hour service 2. Perform the 50-hour service
Date, mtr reading, stamp, sign
300-Hour Service
SERVICE JOURNAL
Action
Date, mtr reading, stamp, sign
At Least Once Each Year
SERVICE JOURNAL
Action
English-73
SERVICE JOURNAL
Action
Date, mtr reading, stamp, sign
English-74
SERVICE JOURNAL
Action
Date, mtr reading, stamp, sign
Page
SECTION 6 PROCEDURE TO OBTAIN WARRANTY CONSIDERATION
WARRANTY STATEMENT
SECTION 1 LIMITED WARRANTY
SECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY
03/27/08
P/N 539 132401 R01