English
Operators Manual
MZ5225
MZ6125
Page
Contents
Driving and Transport on Public Roads
Page
INTRODUCTION
Congratulations
General
Driving and Transport on Public Roads
Good Service
Manufacturing Number
Please have these available when ordering spare parts
INTRODUCTION
symbols and decals
Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx
IMPORTANT INFORMATION
xxxxxx
symbols and decals
remove safety
remove key before
Moving sharp blades under cover
General Operation
SAFETY
Safety Instructions
SAFETY
Operate machine only in daylight or good artificial light
SAFETY
Personal Safety Equipment
Slope Operation
Children
SAFETY
Safe Handling of Gasoline
The engine and the exhaust system become very hot during operation
There is risk for burns if touched
SAFETY
SAFETY
General Maintenance
Use protective glasses for maintenance work
English-15
SAFETY
Risk of sparking
SAFETY
Transport
IMPORTANT INFORMATION
Roll over Protection system ROPS
SAFETY
CONTROLS
Control Locations
1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse
1. Steering Control Levers
CONTROLS
4. Blade Switch
2. Parking Brake
3. Throttle Control
CONTROLS
5. Ignition Switch
6. Choke Control
7. Fuses
CONTROLS
8. Fuel Tank
The engine and the exhaust system, become very hot during operation
Risk for burns if touched
CONTROLS
9. Fuel Shut Off Valve
10. Lifting Lever for the Mower Deck
IMPORTANT INFORMATION Always use the high position to transport
CONTROLS
11. Seat Adjustment Lever
12. Hour Meter
13. Tracking Knob
CONTROLS
operation
Training
Steering
To move forward and backward
operation
Before Starting
Starting the Engine
operation
Press the control for disengaging the mower deck
Place controls in neutral position
Set the throttle
operation
Set the choke control
Fuel valve in the OPEN position
Turn to START position
operation
IMPORTANT INFORMATION
Release ignition to the RUN position
Set the engine speed
Starting the engine with a weak battery
To attach jumper cables
To remove cables, reverse order
operation
operation
Ensure that no one is near mower when engaging blade switch
Running
IMPORTANT INFORMATION
Operating on hills
operation
Mowing Tips
operation
Stopping the Engine
operation
IMPORTANT INFORMATION Tighten the valve moderately
Pump release valves
operation
MAINTENANCE
Maintenance Schedule
MAINTENANCE
English-37
Battery
Always use protective glasses when handling the battery
To clean battery and terminals
Replacing battery
Safety System
Ignition System
Fitting the wrong spark plug type can damage the engine
MAINTENANCE
Engine Cooling Air Intake
Throttle Cable
Choke Cable
MAINTENANCE
Air Filter Maintenance
Do not use compressed air to clean the air filter
Do not tap filter to clean this could cause damage to the sealing
Servicing Precleaner
Replacing the Fuel Filter
Fuel Pump Air Filter
Tire Pressures
MAINTENANCE
Parking Brake
V-belts
MAINTENANCE
IMPORTANT INFORMATION
Deck belt installation
Deck belt
Deck belt removal
MAINTENANCE
Belt installation
Pump Belt
Cutting Blades
Replacing pump belt
IMPORTANT INFORMATION Special blade bolt is heat treated
Replace with a Husqvarna bolt if required
Do not use lower grade hardware than specified
MAINTENANCE
Adjusting the Mower Deck
Before performing any service or adjustment checklist
2. Place the Blade switch in the disengaged position
3. Turn ignition switch to “OFF” position and remove the key
Adjust anti-scalp rollers with the mower on a flat level surface
Anti-scalp rollers
MAINTENANCE
IMPORTANT INFORMATION
Cleaning and Washing
Use protective glasses when cleaning and washing
Removal and installation of caster wheel
Caster Wheels
LUBRICATION
Change transaxles transmission filters
General
LUBRICATION
Lubricating the Cables
1. Front Wheel Mount
2. Front Wheel Bearings
Engine Oil
Avoid skin contact wash with soap and water in case of spills
4. Engine Oil Filter
5. Changing the Engine Oil
LUBRICATION
Engine Oil Levels
Never fill to above the “FULL” mark
Purging Procedures
Hydraulic Pump
Fluid Change
LUBRICATION
Cause
TROUBLESHOOTING
Problem
TROUBLESHOOTING
Problem
Cause
English-56
Service
STORAGE
Storage
Winter Storage
schematics
TECHNICAL DATA
MZ5225
MZ6125
MZ5225BF
Overall Dimensions
Productivity
TECHNICAL DATA
MZ5225
MZ7227
MZ25
TECHNICAL DATA
Engine
TECHNICAL DATA
Overall Dimensions
MZ7227
MZ25
TECHNICAL DATA
Accessories
Torque Specifications
TORQUE SPECIFICATIONS HEX HEAD CAP SCREWS
U.S. Standard Hardware
Metric Standard Hardware
TECHNICAL DATA
CE requirements
CONForMITY CERTIFICATES
USA requirements
SERVICE JOURNAL
Delivery Service
Action
Date, mtr reading, stamp, sign
After the First 5-8 Hours
SERVICE JOURNAL
Action
Date, mtr reading, stamp, sign
25-Hour Service
SERVICE JOURNAL
3. Check the tire pressures 4. Check battery with cables
5. Lubricate according to lubrication chart
50-Hour Service
SERVICE JOURNAL
1. Perform the 25-hour service
2. Clean/replace the air cleaner’s filter cartridge paper filter
100-Hour Service
SERVICE JOURNAL
1. Perform the 25-hour service 2. Perform the 50-hour service
3. Change the engine oil filter 4. Clean/replace the spark plugs
300-Hour Service
SERVICE JOURNAL
Action
Date, mtr reading, stamp, sign
At Least Once Each Year
SERVICE JOURNAL
Action
Date, mtr reading, stamp, sign
SERVICE JOURNAL
Action
Date, mtr reading, stamp, sign
English-73
SERVICE JOURNAL
Action
Date, mtr reading, stamp, sign
English-74
Page
WARRANTY STATEMENT
SECTION 1 LIMITED WARRANTY
SECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY
SECTION 6 PROCEDURE TO OBTAIN WARRANTY CONSIDERATION
P/N 539 132401 R01
03/27/08