MZ5225
English
Operators Manual
MZ6125
Page
Contents
Driving and Transport on Public Roads
Page
General
INTRODUCTION
Congratulations
Driving and Transport on Public Roads
Please have these available when ordering spare parts
Good Service
Manufacturing Number
INTRODUCTION
IMPORTANT INFORMATION
symbols and decals
Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx
xxxxxx
remove key before
symbols and decals
remove safety
Moving sharp blades under cover
General Operation
SAFETY
Safety Instructions
SAFETY
Operate machine only in daylight or good artificial light
SAFETY
Personal Safety Equipment
Slope Operation
Children
SAFETY
There is risk for burns if touched
Safe Handling of Gasoline
The engine and the exhaust system become very hot during operation
SAFETY
SAFETY
General Maintenance
Use protective glasses for maintenance work
English-15
SAFETY
Risk of sparking
SAFETY
Transport
IMPORTANT INFORMATION
Roll over Protection system ROPS
SAFETY
CONTROLS
Control Locations
1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse
1. Steering Control Levers
CONTROLS
3. Throttle Control
4. Blade Switch
2. Parking Brake
CONTROLS
7. Fuses
5. Ignition Switch
6. Choke Control
CONTROLS
Risk for burns if touched
8. Fuel Tank
The engine and the exhaust system, become very hot during operation
CONTROLS
IMPORTANT INFORMATION Always use the high position to transport
9. Fuel Shut Off Valve
10. Lifting Lever for the Mower Deck
CONTROLS
13. Tracking Knob
11. Seat Adjustment Lever
12. Hour Meter
CONTROLS
Steering
operation
Training
To move forward and backward
operation
Before Starting
Starting the Engine
Place controls in neutral position
operation
Press the control for disengaging the mower deck
Set the throttle
Fuel valve in the OPEN position
operation
Set the choke control
Turn to START position
Release ignition to the RUN position
operation
IMPORTANT INFORMATION
Set the engine speed
To remove cables, reverse order
Starting the engine with a weak battery
To attach jumper cables
operation
operation
Ensure that no one is near mower when engaging blade switch
Running
IMPORTANT INFORMATION
Operating on hills
operation
Mowing Tips
operation
Stopping the Engine
operation
IMPORTANT INFORMATION Tighten the valve moderately
Pump release valves
operation
MAINTENANCE
Maintenance Schedule
MAINTENANCE
English-37
To clean battery and terminals
Battery
Always use protective glasses when handling the battery
Replacing battery
Fitting the wrong spark plug type can damage the engine
Safety System
Ignition System
MAINTENANCE
Choke Cable
Engine Cooling Air Intake
Throttle Cable
MAINTENANCE
Do not tap filter to clean this could cause damage to the sealing
Air Filter Maintenance
Do not use compressed air to clean the air filter
Servicing Precleaner
Tire Pressures
Replacing the Fuel Filter
Fuel Pump Air Filter
MAINTENANCE
MAINTENANCE
Parking Brake
V-belts
IMPORTANT INFORMATION
Deck belt removal
Deck belt installation
Deck belt
MAINTENANCE
Cutting Blades
Belt installation
Pump Belt
Replacing pump belt
Do not use lower grade hardware than specified
IMPORTANT INFORMATION Special blade bolt is heat treated
Replace with a Husqvarna bolt if required
MAINTENANCE
2. Place the Blade switch in the disengaged position
Adjusting the Mower Deck
Before performing any service or adjustment checklist
3. Turn ignition switch to “OFF” position and remove the key
MAINTENANCE
Adjust anti-scalp rollers with the mower on a flat level surface
Anti-scalp rollers
IMPORTANT INFORMATION
Removal and installation of caster wheel
Cleaning and Washing
Use protective glasses when cleaning and washing
Caster Wheels
LUBRICATION
Change transaxles transmission filters
General
1. Front Wheel Mount
LUBRICATION
Lubricating the Cables
2. Front Wheel Bearings
4. Engine Oil Filter
Engine Oil
Avoid skin contact wash with soap and water in case of spills
5. Changing the Engine Oil
LUBRICATION
Engine Oil Levels
Never fill to above the “FULL” mark
Fluid Change
Purging Procedures
Hydraulic Pump
LUBRICATION
Cause
TROUBLESHOOTING
Problem
Cause
TROUBLESHOOTING
Problem
English-56
Storage
Service
STORAGE
Winter Storage
schematics
MZ6125
TECHNICAL DATA
MZ5225
MZ5225BF
TECHNICAL DATA
Overall Dimensions
Productivity
MZ5225
TECHNICAL DATA
MZ7227
MZ25
Engine
MZ7227
TECHNICAL DATA
Overall Dimensions
MZ25
TECHNICAL DATA
Accessories
Torque Specifications
Metric Standard Hardware
TORQUE SPECIFICATIONS HEX HEAD CAP SCREWS
U.S. Standard Hardware
TECHNICAL DATA
CE requirements
CONForMITY CERTIFICATES
USA requirements
Action
SERVICE JOURNAL
Delivery Service
Date, mtr reading, stamp, sign
Action
After the First 5-8 Hours
SERVICE JOURNAL
Date, mtr reading, stamp, sign
3. Check the tire pressures 4. Check battery with cables
25-Hour Service
SERVICE JOURNAL
5. Lubricate according to lubrication chart
1. Perform the 25-hour service
50-Hour Service
SERVICE JOURNAL
2. Clean/replace the air cleaner’s filter cartridge paper filter
1. Perform the 25-hour service 2. Perform the 50-hour service
100-Hour Service
SERVICE JOURNAL
3. Change the engine oil filter 4. Clean/replace the spark plugs
Action
300-Hour Service
SERVICE JOURNAL
Date, mtr reading, stamp, sign
Action
At Least Once Each Year
SERVICE JOURNAL
Date, mtr reading, stamp, sign
Date, mtr reading, stamp, sign
SERVICE JOURNAL
Action
English-73
Date, mtr reading, stamp, sign
SERVICE JOURNAL
Action
English-74
Page
SECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY
WARRANTY STATEMENT
SECTION 1 LIMITED WARRANTY
SECTION 6 PROCEDURE TO OBTAIN WARRANTY CONSIDERATION
P/N 539 132401 R01
03/27/08