Engine RPM setting

The Hustler Z Diesel is designed so that the engine will run at 2950 rpm static pump load only. At this speed the hydraulic pumps are running at their maximum rated speed.

Deck leveling and height adjustment

The mower deck has three areas that may need to be checked and adjusted periodically. Before considering any mower deck leveling adjustments, check that the tire air pressure is within the specified range.

DECK LEVEL ADJUSTMENTS

Leveling the deck must be done in the following manner and order:

1.Check tire pressures to make certain they are properly inflated before starting to level deck. The recommended pressures are as follows:

Drive Wheels

8-12 PSI

Front Wheels

8-12 PSI

WARNING: Stop engine. Make sure deck clutch switch is in the down (OFF) position. Remove igni- tion key. Place control levers in the brake position before leaving machine.

2.Park the unit on a flat surface.

3.Raise deck and place 3" of blocking under all 4 corners of the deck (FIG. 61). This will set the cutting height at 3 ½". NOTE: Back of deck will automatically be set ¼" higher.

4.Set cutting height at 3½" in the height indicator by placing the height adjusting stop in the 3½" hole, and turning the height stop so that the pin side is against the stop handle, FIG. 62.

5.Clamp the height adjusting stop against the stop handle. This will assure that the height will not move during the setting process. Otherwise, spring pressure from the deck lift springs will tend to pull the stop away from the handle.

6.Loosen all nuts on the deck lift threaded rods, and the hardware on the adjuster (on the right front), until all the deck lift chains are loose, and the deck is sitting tightly on all four blocks (FIG. 63, FIG. 64 & FIG. 65).

7.Loosen the two nuts on the front of height indicator so that the foot pedal is free (FIG. 66).

8.Start the leveling process on the left front of the tractor.

STOP

HANDLE

BLOCKS

FIG. 61

FIG. 62

9.Set the amount of threads protruding on the deck lift rod from the lift block at approximately 1" (FIG. 67).

10.Jam both nuts against the block.

HEIGHT

ADJUSTING

STOP

11.Push or pull on the deck lift foot pedal until the chain on the left front just becomes tight, making sure that the deck stays tight against the 3" block.

12.While keeping the chain tight, tighten the nuts against the deck lift block on the height indicator rod (FIG. 66).

13.Go to the right front of the tractor.

14.Loosen the 5/16" jam nut on the adjuster lift chain (FIG. 65), and back the adjuster bolt out to allow the adjuster to move up and down freely.

10-35

109706 10/08

Page 148 Page 150
Page 149
Image 149
Hustler Turf Diesel Z manual Engine RPM setting, Deck leveling and height adjustment
Page 148 Page 150

Diesel Z specifications

The Hustler Turf Diesel Z is a powerhouse in the world of commercial landscaping and residential mowing solutions. Designed with an eye for durability, efficiency, and ease of use, this zero-turn mower is equipped with a multitude of features that cater to both professional landscapers and serious homeowners.

One of the standout characteristics of the Diesel Z is its robust diesel engine. These engines offer superior torque and fuel efficiency, enabling extended operation periods without frequent refueling. With a torque-rich performance, users can tackle the toughest mowing conditions, from dense grass to uneven terrain, ensuring a clean and precise cut every time.

The design of the Diesel Z emphasizes operator comfort and control. It features an ergonomic seat with ample cushioning and lumbar support, allowing for extended use without discomfort. The fully adjustable lap bars and controls are intuitive, allowing even novice users to master operation quickly. The mower’s zero-turn capability allows for exceptional maneuverability, making it easy to navigate around obstacles and achieve that professional-looking finish in tight spaces.

Equipped with Hustler’s advanced cutting technology, the Diesel Z provides a premium mowing experience. Its cutting deck is engineered for optimal airflow, resulting in clean and evenly distributed grass clippings. Users can choose from various cutting options, with cutter heights that can be adjusted to suit different grass types and conditions.

For enhanced performance and durability, the Diesel Z is built with a rugged frame and high-quality materials. The solid construction ensures that it withstands the rigors of daily use, while the mower's maintenance-friendly design incorporates easily accessible components for routine service and care.

In terms of technology, the Hustler Turf Diesel Z also integrates advanced features such as LED lighting for improved visibility during low-light conditions and a fuel management system that optimizes performance. With a variety of deck sizes available, users can select the ideal configuration for their specific needs, further enhancing its versatility.

Lastly, the Diesel Z comes with a comprehensive warranty, underscoring Hustler’s commitment to quality and customer satisfaction. In a competitive market for zero-turn mowers, the Hustler Turf Diesel Z stands out as a reliable, efficient, and user-friendly option for anyone looking to upgrade their mowing experience. With its combination of power, comfort, and cutting-edge technology, it is truly a top choice for landscaping needs.
Top Page Image Contents